Kübelwagen Type 82

1
June 17, 2022
The left rear wheel will be with an flat tire. I cut the bottom of the wheel down to the rim, then glued a piece of extra plastic, wider than the wheel, and cut out the rubber wrinkles.
2
June 17, 2022
3
June 17, 2022
4
June 17, 2022
5
June 17, 2022
6
June 19, 2022
Reckless driving leads to bitter consequences...
7
June 19, 2022
8
June 19, 2022
9
June 19, 2022
10
June 23, 2022
I redid one spotlight - thinned the plastic and polished the inside. I want to make it with broken glass.
11
June 23, 2022
I reworked the rear and filled the gaps inside the engine bay.
12
June 23, 2022
13
June 23, 2022
14
August 20, 2022
Prepared a place for the engine
15
August 20, 2022
I have started making an engine from scratch (plastic card 0.5 and 0.3 mm, sprue). This is just the start...
16
August 20, 2022
Another detail of the engine: I started making a generator from the sprue (a long sprue is more convenient to hold in hands, the generator itself, of course, will be short)
17
August 20, 2022
Not finished engine. There are no details yet - a fuel pump, a generator, pipes, wires, etc.
18
August 26, 2022
Engine from scratch. For that, I used 0,3 and 0,5 mm plastic cards, sprue, and a few bolts from Meng Nuts and Bolts set A (small). While there is no carburetor, pipes, and wires
19
January 6, 2023
Started from scratch to make a carburetor with a cylindrical air filter. Imitation of rubber connecting hoses made of masking tape. There are no pipes, levers, or rods on the carburetor yet.
20
February 11, 2023
More details. I reworked the distributor (made it smaller), added levers to the carburetor, and tubes for the mix and ignition wires. The tube for ignition cables is made from the syringe needle, for the mix - is from stretched sprue.
21
March 26, 2023
I made door handles from 0.5 mm copper wire. Also made loops for the awning. For this, I used a 0.2 mm copper wire.
22
March 26, 2023
Supports for Windshield are made from a beer can tin.
23
March 26, 2023
I made a toolbox from scratch, cut off plastic straps from the awning, corrected the folds, and made new straps from a thin aluminum sheet.
24
March 26, 2023
From a black fishing line 0.3 mm, I made brake lines.
25
March 26, 2023
I made the wheels turned
26
March 26, 2023
Steering gear and rods from scratch. For the rods, I use 0,5 mm copper wire.
27
July 6, 2023
On the back seat will be a very interesting German optical communication device - Li Spr 80. I started making boxes for this equipment and prepared a weight-deformed place on the seat for them.
28
July 6, 2023
29
July 6, 2023
From scratch, I started making Li Spr 80 device. This is a front-end panel. Not finished yet, there must be two regulators, four radio tube handles, three more sockets, wires, and so on.
30
July 8, 2023
Tripod for the optical part of the device Li Spr 80 from scratch
31
July 19, 2023
The optical part of Li Spr 80 is made from scratch. Lenses from a transparent lid from a yogurt.
32
July 19, 2023
33
October 15, 2023
I finished making boxes for Li.Spr.80.
The frames of the boxes are made from aluminum tin from wine cork.
The black stains look terrible, they are from black CA glue, but I hope after painting, they won't be seen.
34
October 15, 2023
35
October 15, 2023
36
October 15, 2023

Comments

66 17 June 2022, 14:23

Jan Peters
Looks like you've got a flat tyre.
Following this with interest

17 June 2022, 14:47

Vytautas
Thanks, chaps!

17 June 2022, 20:52

Spanjaard
nice looking flat tire. will make a nice dio 🙂

17 June 2022, 23:14

Hans
Photo 1: 😂😂

23 June 2022, 12:20

Dominik Weitzer
nice work on the fenders! like it a lot.

23 June 2022, 14:51

Vytautas
Thank you, chaps, for your kind words!

24 June 2022, 21:38

Rui
Taking a seat 👀

25 June 2022, 01:09

Rui S
I like it 👍 I'm in no doubt 😎

25 June 2022, 14:32

Vytautas
Thanks, guys, for your interest!

25 June 2022, 16:05

Bruce Huxtable
Watching with interest, and liking where this is going 👍🙂

25 June 2022, 16:44

Guy Rump
Looking good 👍

20 August 2022, 13:44

Bruce Huxtable
Can't believe your micro sculpting skills 👍 May I ask how you altered the fender? Hot water? Hot hair drier? I'm liking where this is going, Guy 👍🙂

20 August 2022, 15:17

Vytautas
Hi, Guy Rump, Bruce, thank you for your kind words!

About sculpting:
Hot water, pliers, hair dryer, etc. - are technologies that I do not use because it is impossible to control the final result. I use a simple carving - in this case, I can make exactly what I want.
I explained my method here: britmodeller.com/for..644-plastic-carving/

20 August 2022, 15:50

Bruce Huxtable
Many thanks, Vytautas, your skills are creating a little gem. I think I'll give these techniques a try., but I'll need a few crumpled cars for inspiration!

20 August 2022, 17:53

Vytautas
Hi again Bruce
I like your idea of rumpled cars!
Once upon a time, I planned to make a heavily damaged luxury car, one of those that all modelers make shiny and sparkling, for example, the Ferrari Pininfarina or Enzo...
But then I realized that military vehicles are more interesting to me

20 August 2022, 18:11

Bruce Huxtable
One day, the urge will return, Vytautas, and I can't wait to see an un-loved and battered supercar 😉

20 August 2022, 20:32

Michael Kohl
Nice progress here. Like the flat tire where it is difficult to achieve a convincing impression with molded plastic wheels.

7 January 2023, 08:40

Rui S
Amazing detailing 👍

11 February 2023, 17:30

Guy Rump
Looking good. 👍

26 March 2023, 19:10

Neil
Hi Vytautas 🙂 following also 👍

28 March 2023, 21:02

Pietro De Angelis
Complete assistance service, tire specialist, mechanic and body shop, wow!

6 July 2023, 23:51

Villiers de Vos
Very nice progress.

7 July 2023, 03:29

Doubtingmango
Love all the detail

7 July 2023, 03:44

Dominik Weitzer
excellent progress. those deatil on the engine, body are top

7 July 2023, 07:16

Spanjaard
Those details are just awesome...... engine is amazing

7 July 2023, 07:31

Jan Peters
I agree, great attention to detail, even if most isn't really seen after finishing the model

7 July 2023, 12:29

Neil
Agree with others Vytautas. This is just fabulous to see appear again, I have great admiration for your scratch work ability, very impressive indeed 👍

7 July 2023, 12:46

Vytautas
Thank you all, chaps!

8 July 2023, 12:16