Spitfire FR IXc MK915 - pink recce

1
July 14, 2019
Project inventory
2
July 16, 2019
First step: erasing the wrong wheel bulges and filling in the rivets in front of the main wing spar
3
July 20, 2019
Camera bay door cut out
4
July 20, 2019
Heavy thinning on the inner side of the fuselage
5
July 20, 2019
All rivets on the door filled, ready for the camera window and new rivets
6
July 24, 2019
size comparison of bulkhead no.11: scale drawing vs. Revell vs. Eduard
7
July 24, 2019
Shrunk cross sections no.13 and 14 to match width of Eduards's bulkhead no.12
8
July 24, 2019
bulkheads in place. I'll be adding one more layer of styrene and then the final shape will be cut
9
July 24, 2019
Cockpit door opening enlarged by around 2mm
10
August 4, 2019
Bulkheads no.13 and 14 completed - far from perfect but good enough for the small camera hatch
11
August 4, 2019
CAD sketch of the F.24 camera
12
August 10, 2019
draft fr the F24 camera
13
August 19, 2019
Soem refining on the brassin cockpit - removing unnecessary structure
14
August 19, 2019
moulded on tube - meeeeh
15
August 19, 2019
replaced with 0,2mm copper wire
16
August 19, 2019
drilled open all the lightening holes on the bulkheads; managed to crack the right one
17
August 19, 2019
tried adding the plumbing to the front bulkhead (eduard) which is more than a tad to small compared to Tamiya (left) and Revell (right)
18
August 24, 2019
Revell/brassin bash finished! the sidewalls needed massive thinning to insert the cockpit into the fuselage
19
August 24, 2019
caomparison of the Tamiya head armour vs. eduard - the eduard one is ridiculously wrong and doesn't even fit to the brassin bulkhead
20
August 24, 2019
scartch build head armour from 0,2mm styrene
21
August 24, 2019
all openings on the seat drilled/cut open
22
August 26, 2019
comparison for the seat armour: Barracuda, Tamiya, eduard - scratch build below
23
August 26, 2019
dry fit with the seat; notches added to the ratchet
24
August 26, 2019
dry fit of the whole cockpit - lots of gaps need reworking
25
August 26, 2019
cables added to the voltage regulator
26
August 31, 2019
27
August 31, 2019
28
September 5, 2019
first coat of primer
29
September 12, 2019
black base
30
September 12, 2019
marbling and preshading
31
September 12, 2019
blending with Gunze C364
32
September 12, 2019
and here's the look withou anything else - quite alive already!
33
September 16, 2019
Seat coloured with Tamiya brown and watercolour pencils
34
September 22, 2019
eduard IP painted in NATO black, followed by pure black from below and dark grey from above to produce shadows - quite hard to photograph
35
September 27, 2019
details painted
36
September 27, 2019
37
October 6, 2019
eduard decals: quite thick and no single dials - just why?
38
October 6, 2019
No decal for the compass included - MDC to the rescue!
39
October 6, 2019
unfortunately the placards didn't settle down as I hoped
40
October 6, 2019
pure joy: the Master barrels for the Hispano cannons
41
October 12, 2019
instrument dials in place - clear acetate applied for testing purposes on one of them
42
June 25, 2022
43
February 13, 2020
F.24 cameras SLA printed
44
February 13, 2020
those are tiny!
45
July 4, 2020
46
July 4, 2020
47
November 8, 2020
Another view on the IP; still missing the glass for the gunsight
48
November 8, 2020
sutton belts installed
49
November 8, 2020
50
June 26, 2021
Type 25 camera mounts fresh from the printer
51
July 17, 2021
new cradles for mounting inside the fuselage
52
December 29, 2021
template for re rivetting
53
December 29, 2021
new goodies
54
December 29, 2021
Tamiya - Revell - Barracuda
Find the errors 😄
55
December 29, 2021
the Barracuda part is far superior, but how do I install it with the wings glued?
56
December 30, 2021
fuselage primed and sanded to remove the "mad rivetter's" work
57
December 30, 2021
Really not Revell's A-game with the huge holes (rivets) and the sink marks
58
January 2, 2022
drilled the lower wing on my spare kit
59
January 2, 2022
a quick cut
60
January 2, 2022
and it fits!
61
January 2, 2022
a "little" bit of plastic removed from the upper wing
62
January 2, 2022
and I can get it in with the wings shut!
63
January 2, 2022
looking sharp
64
January 2, 2022
Revell = meh
65
January 2, 2022
much better looking
66
January 2, 2022
cutout made on the test mule with the wings assembled
it takes around twice the time, but it's possible to do so!
67
January 2, 2022
fit isn't perfect but okayish for a dry fit
68
January 6, 2022
69
January 6, 2022
70
January 6, 2022
71
January 6, 2022
72
January 6, 2022
73
October 14, 2022
horrible fit
74
October 14, 2022
all around
75
October 14, 2022
76
October 14, 2022
77
October 14, 2022
wooden spars (3D printed and painted with oils) added to the bulkheads
78
October 14, 2022
camera cradle test fit
79
October 15, 2022
80
October 15, 2022
81
October 30, 2022
Why Revell?
There shouldn't be a gap here...
82
October 30, 2022
The lower belly fix leads to nasty gaps on the wing roots
83
October 30, 2022
84
October 30, 2022
styrene shee to the rescue
85
October 30, 2022
86
October 31, 2022
Wrestling the wings into submission to get a consistent dihedral
87
October 31, 2022
port wing now without spacers but with loads of glue
88
November 6, 2022
seams filled and sanded
89
November 6, 2022
much better now
90
November 6, 2022
Another seam...
91
January 6, 2023
92
January 6, 2023
93
January 6, 2023
94
January 6, 2023
95
January 6, 2023
filled the gaps with Milliput
96
January 8, 2023
fillered with Mr. Surfacer 500
97
January 8, 2023
added a glue interface for the carb intake
98
January 8, 2023
glued shut at the rear; notice the gap at the front
99
January 8, 2023
fix for the front tested
100
January 8, 2023
after setting time the front portion was forced shut
101
January 8, 2023
0.5 mm shim added to the front fuselage
102
January 8, 2023
trimmed to shape
103
January 8, 2023
looking okayish

Comments

25 14 July 2019, 14:51

Urban Gardini
Nice, I'm planning to do the same bird but with the Tammy kit.

16 July 2019, 20:15

Gordon Sørensen
Great work, Joachim! I am wanting to do this in 1/72 too.

21 July 2019, 13:27

Joachim F.
Nice to hear mates - more pink Spitfires!

24 July 2019, 06:36

Urban Gardini
Yes, the world needs more pink Spits...!

24 July 2019, 09:36

Holger Kranich
A pink Spitty? Splendid, hell i am in!😢

24 July 2019, 09:50

Joachim F.
For those who may doubt the pink(ish) colour:
ipmsrealcote.com/art..pitfire/pinkspit.htm

24 July 2019, 11:58

Holger Kranich
A camo for dusk and dawn... Very interesting!

24 July 2019, 12:18

Dave Flitton
Interesting build - watching

24 July 2019, 15:27

Stefan Schacht
nice start, i take a seat

12 September 2019, 19:55

Joachim F.
Make sure it's comfortabel - this may take a while

16 September 2019, 19:14

Joachim F.
Well I got my brassin cockpit for a bargain. So in my case it's the same price as the kit 😄
The details are beautiful but the eduard shrunk all dimensions especially if you compare them to Tamiya..

27 September 2019, 18:47

Rui S
Looking great. 👍 I'm in

4 July 2020, 22:08

Choppa Nutta
good looking cockpit

4 July 2020, 22:35

Alberto
It looks awesome... very humbling for us mere aficionados

8 November 2020, 12:32

Rui S
I agree with Al Berto. Impressive work on the pit, Excellent paintjob 👍

8 November 2020, 12:44

Urban Gardini
Coming along just fine!

8 November 2020, 13:24

Joachim F.
If you could just see me blushing in front of my screen 😄
Thank you very much mates, I'm trying to do my best on this one

8 November 2020, 16:48

Mathieu
Lovely work. taking a seat.

29 June 2021, 14:12

Dave Flitton
Looking really good!!!

29 June 2021, 15:27

Spanjaard
wow, amazing job on that cockpit. looking forward the rest!

29 June 2021, 15:37

Joachim F.
Thanks mates!
It may take some time for the next steps since I'm waiting for PE parts from AIMS to dress up the camera bay door.

29 June 2021, 19:47

Urban Gardini
Are the cameras of your own design? I would be interested in buying a set to my Pink Spitty from you if it's possible.

29 June 2021, 21:18

Joachim F.
Yes, I made them based on measurements from a mate over on LSP and another friend of mine did the 3D printing. Not intending to sell them. Shoot me a message if you're interested in the .stl file.

30 June 2021, 06:43

Urban Gardini
I'll do that and find someone more local that can print it for me.

30 June 2021, 10:07

Guy Rump
Looking good. 👍

15 October 2022, 16:47

Joachim F.
We're getting there - slowly 😄

17 October 2022, 07:55

Project info

Spitfire FR IXc

103 images

1:32

On hold

1:32 Spitfire Mk. IXc cockpit (Eduard 632111)

1:32 Spitfire Mk.IX Exhaust stack - Fishtail (Eduard 632108)

1:32 Supermarine Spitfire C wing - Hispano 20mm cannons in fairings (Master AM-32-016)

All albums

View all albums »