scale modeling database | stash manager
tom...
Tom ... (tom...)
US

Tamiya: Jeep Willys MB - WIP

Album image #1
Getting Started. Not too many parts but they are small. 
 

Album image #2
Assembled as much of the sub-sections as possible. Luckily most things are the same color.  
 

Album image #3
Using Tamiya's lacquer primer as the model pieces are too small to rough up with sand paper.  
 

Album image #4
You can see what pieces I pre-assembled for the main body. 
 

Album image #5
Same for the chassis. Even though I did remove a lot of seams priming showed what ones I missed.  
 

Album image #6
Everything primed and all the main airbrushing done. Need to finish hand painting parts and then clear coating. 
 

Album image #7
Album image #8
Album image #9
Completed hand painting details and parts. Omitting driver and some weapons till after the car is assembled 
 

Album image #10
Everything ready for clear coat. Used Alclad's Aqua Gloss. 
 

Album image #11
Decal'ing done 
 

Album image #12
Alclad's Aqua Gloss didn't like residue from the main decal... not sure if it's the micro set/sol. Lesson learnt to wash off residue before continuing 
 

Album image #13
Need to find a better Q-tip...  
 

Album image #14
Trying out dirt deposit... definite learning curve ahead...  
 

Comments

1 17 April 2019, 05:06
Tom ...
Building this jeep in order to try out weathering techniques.

It's a long long time since I did a military build (like 40 years). I do like that most of the vehicle is one color so can pre-build a lot of it before painting.

Did a lot of seam removal but priming showed I missed a bunch. Argh... Done all of the airbrush work. Need to hand paint the rest and then will gloss coat to protect and prepare for washes. Trying to figure out if I use Future or Alclad's Aqua Gloss....
17 April 2019, 05:19
Rui S
Looking forward to see your work in this one 👍
17 April 2019, 09:57
Neuling
Me too ...............
17 April 2019, 18:25
Tom ...
Really enjoyed hand painting the details and smaller parts. Didn't get creative, just followed Tamiya's color directions.

Clear coated with Alclad Aqua Gloss. Very nice to work with but I do struggle with getting good coverage on all the weird surface angles and crannies. Same thing for the primer but the issue there was the paint drying too quickly and creating a lot of "dust" in the crannies, like the wheel wells and the interior surfaces of the cab.
18 April 2019, 05:56
Chris Greathouse
Look really good Tom 🙂
18 April 2019, 06:27
Dave Flitton
Watching
18 April 2019, 16:06
Tom ...
Finished decal'ing and clear coating. However had strange interaction between the clear coat and decal residue as you can see here in pic #12: Tamiya: Jeep Willys MB - WIP | Album by tom... (1:35)

I guess I need to wash away any decal solution residue before continuing! Hopefully it's not noticeable with the final mate coating.
19 April 2019, 21:10
Chris Greathouse
Good luck with the fix.
19 April 2019, 21:19
Bob Hall
Just think of it as your first step into weathering, remember ! it's a war vehicle.
19 April 2019, 21:22
Rui S
I agree With Robert...
19 April 2019, 21:26
Tom ...
Yes with this model it's not really an issue... and the next step is weathering. I have a few AK Interactive washes I'm going to play with, as well as Tamiya's weathering powders. If you look at my paint stash you can see what I have: tom...

I have to say that while I really enjoy looking at other peoples' extremely weathered models I'm not one for rust buckets and mud monsters myself. I'm hoping to have a slightly worn and dusty jeep with a bit of mud... hoping that is... most likely this will all go south very quickly 🙂

Also looking forward to painting the driver. Don't know what I'm doing there either but I'm thinking it'll be fun.
19 April 2019, 21:50
Chris Greathouse
I painted my first fig with the arcade. It was kind of exciting, but I didn't know what I was doing. For him to go from sprue color to painted was a fun process. I hope you have fun too!
19 April 2019, 22:05
Tom ...
Did an initial "panel wash" to bring out details. Need to find a better Q-tip. I have the Tamiya ones but they are too compact.... need to find something in between...

Also tried out AK Interactive's dirt deposit wash on the under carriage... hmmmm, I've got a long way to go in order to get any good at this.... still it's interesting and fun trying.... this might just end up a muddy mess all the same. Oh well.
20 April 2019, 02:36
Nathan Dempsey
That dirt and dust deposit stuff looks interesting. I may have to pick up a bottle.
20 April 2019, 03:33
Tom ...
James, I didn't resolved it. In this case I don't think it's going to matter as when I do a final matte coat it shouldn't be noticeable. However, in future I'm going to get into the habit of washing off decal'ed areas to ensure there's no residue left.
22 April 2019, 21:32
Chris Greathouse
That interesting... I have lakes of micro set when I decal, aside from the usual mop up/squeegeeing the liquid from under the decal I don't clean anything, I just let it dry for a few+ hours before I spray Future.
22 April 2019, 22:53
Tom ...
I feel like it might have been due to the decal's adhesive. I've also never had a problem before with micro set and sol. But also this was the first time I used Alclad's Aqua Gloss for coating decals so maybe it's some weird interact between them all. Like you say... interesting...
22 April 2019, 23:43

Album info

Building this to try out basic weathering.

14 images
1:35
On hold
1:35 Jeep Willys MB (Tamiya 35219)

All albums

View all albums »