scale modeling database | stash manager
yuri
Julian Herrero aka Yuri (yuri)
ES

Citroën Mehari Heller 1/24

Album image #1
Kit box 
 

Album image #2
Box contents 
 

Album image #3
Sprues 
 

Album image #4
Sprues 
 

Album image #5
Sprues 
 

Album image #6
Sprues 
 

Album image #7
Let's start with the engine block and suspension arms. 
 

Album image #8
Chassis pan 
 

Album image #9
Workbench 
 

Album image #10
Cylinders need some putty 
 

Album image #11
Some green putty ... 
 

Album image #12
A bit of detail has been added to the engine 
 

Album image #13
Some stretched sprue strakes added to the sump 
 

Album image #14
Cylinders and carb glued to the block 
 

Album image #15
Also disk brakes haven been glued 
 

Album image #16
Suspension arms glued to the chassis pan. The joint is too weak and I had to reinforce it with with CA glue. 
 

Album image #17
Admission ducts and front fan added 
 

Album image #18
Engine 
 

Album image #19
Engine 
 

Album image #20
Engine 
 

Album image #21
Chassis with marked section to be removed. Sump did not fit in the opening. 
 

Album image #22
More progress on the engine. Now with air intakes and exhausts shrouds have been glued in place. 
 

Album image #23
Checking the mudguards and engine clearance with blue-tack. Just to check if the engine fits properly before it's too late. 
 

Album image #24
Engine almost finished wiht air filter box glued. 
 

Album image #25
Hand painting the recesses which will be difficult to reach with an airbrush. Tamiya X-6 gloss orange which is a perfect match to me. 
 

Album image #26
Finished engine. 
 

Album image #27
Finished engine with exhausts connected to the muffler. 
 

Album image #28
Engine mated to the chassis 
 

Album image #29
When the mufflerwas fixed in its proper place in the chassis , I couldn't connect it to the exhausts , so I replaced the "rigid" plastic parts with vinyl tubing. 
 

Album image #30
Some sink marks to be dealed  
 

Album image #31
Checking chassis and body fit. 
 

Album image #32
Done ... heating hoses were added from vinyl tube (white). 
 

Album image #33
Brake pump "tank" made from a plastic tube and a styrene disc. 
 

Album image #34
Album image #35
ARRRGGGG .... front disk lines added ... which now (April 2021) working on a 2CV pic-up found that this is not correct . The engine has inboard disk brakes , which is quite clear in picture 29.
🙁😭((( 
 

Album image #36
Completed fuel pump plus tubing. Also hand brake converted from a left-over part of the kit. 
 

Album image #37
I lost one wind-screen wiper ... so I had to scratchbuilt both .... I'm quite pelased with the result 
 

Album image #38
The kit does not include glass for the head lamps ..... Spare box came to rescue  
 

Album image #39
Wind scrren wipers made from scratch. Look the part to me. 
 

Album image #40
Metallic disc to cover the holes for the canvas were made with lead from a wine bottle capsule and Waldron Punch & Die Set ... colour is perfect as is .... 😉 
 

Album image #41
Adding straps for the bonnet ,,, not very true to scale ,,, but made to allow removing of the bonnet .... and putting it back again 
 

Album image #42
Glued 4 pins to help fixing the bonnet in place. 
 

Album image #43
Completed engine bay. All these items were added : brake pump and lines , heating hoses , electric wiring to the head lamps and the battery , exhaust shrouds , "glass" for the head lamps 
 

Album image #44
Album image #45
Finished in December last year ,,,, it was high time that I post the pictures. 
 

Album image #46
Album image #47
Album image #48
Album image #49
I'm still trying to find a suitable speedometer decal
🙁😭(( 
 

Album image #50
Finished .... hummmm ,,, seeing the pictures I notice some missing items ... i.e. wheels air valves , and brake hoses for the rear wheels ,,,,,, front brakes are inboard. 
 

Comments

9 4 November 2016, 18:23
Julian Herrero aka Yuri
As soon as I saw it in the shop I knew I had to buy it .. and build it asap. In fact it didn't even went to the stash ... went from the shop right to my workbench.
The kit is rather basic in some aspects ... no fuel tank, simplistic fuel filler cap, no clear plastic for the head-lamps .... Nevertheless the engine is quite detailed, but a some tubes and connectors missing. In fact some tubes are on the sprues but not in the instructions ,,, more anon.
Beware, gates to some parts are really tiny and prone to break ... I've just lost one windshield wiper ...
6 November 2016, 17:05
Jorge Ferreira
Congratulations. Not an easy kit to deal with. If we wan`t to make it better our imagination is the limit . I did mine a few years ago and I`m still looking for the right side rear view miror.
26 April 2021, 18:44
MS K
I also made one, and I think it's a very fun kit.
The orange color seems to go very well 🙂
27 April 2021, 16:08
Julian Herrero aka Yuri
Yes ... the kit is really fun to build ... no major build troubles ... What's shocking for such a moder kit is all the parts it lacks ..... headlights glass it's just a flagrant missing
29 April 2021, 13:35
MS K
Oh, I agree. Headlights are clumsy.
29 April 2021, 17:39

Album info

Standard build, with just a few detailing and corrections. Pretty much an OOB job.
As soon as I saw it in the shop I knew I had to buy it .. and build it asap. In fact it didn't even went to the stash ... it went from the shop right to my workbench.
The kit is rather basic in some aspects , all these items are missing :
fuel tank
simplistic fuel filler cap
no clear plastic for the head-lamps
no brake pump
no heating hoses
no speedo
no handbrake lever
no ashtray
no bonnet straps
Nevertheless the engine is quite detailed, but some tubes and connectors are missing. In fact some tubes are on the sprues, which I guess are for the 2CV kit.
I added just a few things to get it right ,but not much more.
I can stand with all that.

50 images
1:24
Completed
No 0,5mm High Flow D?se (t?rkis) (Aztek A9306)No Tamiya Extra Thin Cement (Tamiya 87038)

All albums

View all albums »