The building and painting process.

1
February 23, 2023
And it's finished
2
February 23, 2023
3
February 23, 2023
4
February 23, 2023
5
February 23, 2023
6
February 23, 2023
7
February 23, 2023
8
February 23, 2023
9
February 23, 2023
The whole model was painted with matt varnish, than used super clear III to make the wet mud effect.
10
February 23, 2023
Some other perspective...
11
February 23, 2023
Some other perspective...
12
February 23, 2023
Some other perspective...
13
February 23, 2023
The wet mud is finished.
14
February 10, 2023
Some progress with the weathering... This time I think the mud effect is in quite a good shape. Not finished, because I would like to wait the drying time to check the colors and add some other shade to be more interesting.
15
February 10, 2023
16
February 10, 2023
17
February 9, 2023
Unfortunately, I forgot to drill the exhaust pipe before painting... but never too late. Breaklights, index and some details added too.
18
February 9, 2023
Shovel and axe are painted.
19
February 8, 2023
Just a little carpenter work to upgrade the airbrush station. 🙂 I'm curious about it's working.
20
February 5, 2023
Oil, wash, some detail painting and pigments. It is almost done, some more hours and the BTR is out from factory. 🙂)
21
February 4, 2023
Super Clear varnish and some decals are added. The turret numbering is fictional, but based on pictures.
22
February 1, 2023
I decided to use a lighter shade of green because my previous BTR-60 PB work was a little bit darker than I wanted. The weathering became too emphatic in that case. The plain is to give a laquer layer and after it I will do some additional toning.
23
February 1, 2023
24
February 1, 2023
Base colour and some tones.
25
January 29, 2023
And the primer is finished. There are some inaccuracy, so I will correct some gaps and casting errors.
26
January 29, 2023
I drilled the KPV barrel to give it some realistic look. I didn't buy any metal gun barrel for this kit.
27
January 29, 2023
Some on the turret also...
28
January 29, 2023
Last grab irons are glued.
29
January 26, 2023
30
January 26, 2023
31
January 26, 2023
32
January 26, 2023
33
January 26, 2023

Kommentarer

32 26 January 2023, 21:44

Zsolt Czegle
Kíváncsi vagyok, milyen lesz.... 😉

29 January 2023, 21:04

Rui
Following 👀

29 January 2023, 21:07

SmallScaleIndustry .
Zsolt, látom Te már túl vagy ezen a kiten. 🙂 Szép munka lett.

29 January 2023, 22:37

Finn
Looking good

2 February 2023, 18:53

Saeed Ezadi
Beautiful so far!

3 February 2023, 12:53

Simon Nagorsnik
They are looking good, like them!

3 February 2023, 13:00

SmallScaleIndustry .
Thank you!

3 February 2023, 19:40

Simon Nagorsnik
It's getting better and better👍

5 February 2023, 16:44

Spanjaard
very nice job on this small BTR. And very nice base for the airbrush. i would suggest a small addition. two small horizontal pieces in the left arm, to sit at the sides of the valve, that would avoid the airbrush from rotating. then you can leave the airbrush in that nice base, fully loaded with paint, and not to worry about it spilling the paint accidentally.
you can also make a small hole in the left arm, but then the airbrush need to move forward and may have not much support in the right arm.

10 February 2023, 07:36

SmallScaleIndustry .
Hey Spanjaard! Thank you for the usefull feedback. I admit that I haven't used this setup yet, so you saved a floor cleaning action for me. 🙂)

10 February 2023, 09:30