Polaris MRZR build thread

1
May 25, 2020
Packaging from the shop
2
May 25, 2020
Inside look on the 6 zip-lock packets
3
May 25, 2020
6 Packets inside the box
4
May 25, 2020
unboxing
5
May 26, 2020
most fragile packet with foam wrapped on these 3 parts
Packet A
front bumper rail
rear bumper rail
rear tow hitch
6
May 26, 2020
Packet B
Rollover side bars
Side handle railing
Rollover cross bar
Rear tray railings
7
May 26, 2020
Packet C
Steering columns
Hitch and handles (broken)
Suspension front
Torsion axial front
Torsion axial rear
8
May 26, 2020
Packet D
4 x tire/wheels
Side steps
Tail gate
Rollover front bar
9
May 26, 2020
Packet E
Chassis Front
2 x seats
10
May 26, 2020
Packet F
Chassis Rear
Exhaust
Chassis bottom frame
11
May 26, 2020
Broken part on the tail gate frame brackets
12
May 26, 2020
Frame dimension is smaller than the chassis
13
May 26, 2020
poor alignment between the guidepins 🙁
14
May 28, 2020
Wash and dry from resin kit parts
15
May 29, 2020
Different exhaust design between C2 n MRZR, length longer on the C2
16
May 28, 2020
Comparing the size between the C2 and MRZR
17
May 29, 2020
Filing and prep for front and rear chassis
18
May 29, 2020
Dry fitting after filing
19
May 29, 2020
Axial is turned, to the right

Updated: turned to the same direction
20
May 30, 2020
Parts for axials, suspension, chassis frames and exhaust
21
May 30, 2020
Front axial with suspension
22
May 30, 2020
Rear axial
23
May 30, 2020
Angled to the forward on the front axial. The wheels are aligned straight at this angle.
This is correct?
24
May 30, 2020
Chassis frame front
25
May 30, 2020
Chassis frame rear in 2 pieces
26
May 30, 2020
Easier to fix these axials first before joining the front and rear chassis
27
May 30, 2020
Dry fitting on the axial chassis steps
28
June 1, 2020
29
June 1, 2020
30
June 1, 2020
31
June 1, 2020
32
June 1, 2020
33
June 1, 2020
34
June 1, 2020
35
June 1, 2020
36
June 1, 2020
37
June 1, 2020
38
June 1, 2020
39
June 1, 2020
40
June 1, 2020
41
June 1, 2020
42
June 1, 2020
43
June 1, 2020
44
June 1, 2020
45
June 1, 2020
46
June 1, 2020
47
June 1, 2020
Dry fit on rear bumper and tow hitch
48
June 1, 2020
49
June 1, 2020
50
June 1, 2020
51
July 17, 2020
52
July 17, 2020
53
July 17, 2020
54
July 17, 2020
55
July 17, 2020
56
July 17, 2020
57
July 17, 2020
Assembly on rear axial
58
July 17, 2020
Assembly on front axial
59
July 17, 2020
Assembly on front axial, left side is too high
60
July 17, 2020
Extending tow hitch hole using 0.8mm drill bit
61
July 17, 2020
Tow hitch is still too tight after drilling with 1mm drill bit
62
July 17, 2020
Extending tow hitch hole using 1.5mm drill bit
63
July 17, 2020
Dry fit tow hitch after extending to diameter 1.5mm (bottom view)
64
July 17, 2020
Dry fit tow hitch after extending to diameter 1.5mm
65
July 17, 2020
Dry fit tow hitch after extending to diameter 1.5mm
66
July 17, 2020
Shortening rear bumper rod for tighter fit with chassis
67
July 17, 2020
Rear bumper and tow hitch assembly (bottom view)
68
July 17, 2020
Rear bumper and tow hitch assembly (right view)
69
July 17, 2020
Rear bumper and tow hitch assembly (rear view)
70
July 19, 2020
Fitted the side steps (top view)
71
July 19, 2020
Fitted the side steps (bottom view). A little scrappy on the fittings :-/
72
July 21, 2020
73
July 21, 2020
74
July 21, 2020
75
July 21, 2020
76
July 21, 2020
77
July 21, 2020
78
July 21, 2020
79
July 21, 2020
80
July 21, 2020
81
July 21, 2020
82
July 21, 2020
83
July 21, 2020
84
July 22, 2020
Most frustrating the lug broke again while installing the tailgate. Now back to reworking the lugs again!!??
85
July 22, 2020
Finally managed to break all the tailgate lugs 🙁 🙁 🙁
86
July 22, 2020
87
July 22, 2020
88
July 23, 2020
Broke again! Good thing all the lugs break clean :-/ now I’m quite good at fixing this micro parts
89
July 24, 2020
90
July 24, 2020
91
July 24, 2020
92
July 25, 2020
3 completed without their rollbar
93
July 26, 2020
94
July 26, 2020
95
July 26, 2020
96
July 26, 2020
97
July 26, 2020
98
July 26, 2020
99
July 26, 2020
100
July 26, 2020
101
July 26, 2020
102
July 26, 2020
103
July 26, 2020
104
July 29, 2020
105
July 29, 2020

Comments

4 25 May 2020, 07:54

Kace Wong
Updated on the unboxing before the build starts proper. Checking on the broken parts and any missing parts.

This design is very different from the Commander C2 kit. This has lot lesser parts, less intricate details compared to the C2.

26 May 2020, 12:34

Kace Wong
Started on the build proper. Continue to compare the 2 kits, C2 and MRZR in their design and building steps.

29 May 2020, 10:14

Kace Wong
update: joint the 2 front and rear halves chassis, and dry fitting the rear bumper and tow hitch assembly. progress is slow...

18 July 2020, 08:42