JAS-39D Czech Air Force no. 9820 - Decennial - WIP

1
December 10, 2023
A two-seat Gripen of the Czech Air Force with a special livery for the 10th anniversary of the use of these machines.
2
December 11, 2023
Kit is from Chinese manufacturer Kitty Hawk. The picture on the kit box shows a Swedish JAS-39D.
3
December 11, 2023
The relatively small cardboard box contains a really large number of parts.
4
December 11, 2023
As an addition to this kit I bought the decals for the anniversary machine. Without them, painting would be very difficult.
5
December 11, 2023
I also bought a set of PE parts for this kit.
6
December 13, 2023
I added PE parts for the side instrument panels to the painted cockpit tub.
7
December 13, 2023
I added PE parts for the side instrument panels to the painted cockpit tub.
8
December 13, 2023
I assembled both pilot seats from kit parts. And I started adding PE parts to the assembled seats. Most of them are still missing.
9
December 13, 2023
I assembled both pilot seats from kit parts. And I started adding PE parts to the assembled seats. Most of them are still missing.
10
December 14, 2023
I continued to assemble the nose of the aircraft with both cockpits. Using PE parts with side instrument panels required some modifications.
The instructions in the kit say to glue the plastic parts to the cockpit side panels. However, these parts are too thick and would partially cover the side instrument panels when glued. Therefore, I sanded them as thin as possible. I then glued the parts to the side walls of the cockpits.
11
December 14, 2023
First, I glued the assembled forward landing gear shaft and cockpit tub into the front of the fuselage with the PE parts of the nose side panels glued on.
12
December 14, 2023
I glued the dashboards assembled from PE parts to the sanded parts of the dashboard from the kit. Then I glued the top covers to the dashboards.
13
December 14, 2023
In the nose of the plane (in front of the cockpits) I put a weight of modelling compound and glued the tip of the fuselage.

The instrument panels and pilot seats are not yet complete and are added to the fuselage without gluing just for photography.
14
January 6, 2024
I added etched seat belts to the painted seats. This fun took me two whole hours. Compared to the Italeri belts, Eduard took more care with the Kitty Hawk belts and they look much better. Although the black dots on the belts, which probably represent the stitching on the belts, could have been omittedy.
15
January 9, 2024
I glued the assembled main landing gear shafts to the bottom of the wing.
16
January 9, 2024
I glued the assembled main landing gear shafts to the bottom of the wing.
17
January 9, 2024
I glued a PE instrument panel into the hole in the starboard side of the fuselage.
18
January 9, 2024
Into the rear hole of the APU I glued a grille, assembled from PE parts.
19
January 9, 2024
This air outlet is poorly molded on my model. A piece of it is missing. But even if it was whole, it's still the wrong shape. I'll remove it later and replace it with a new one with the correct shape.
20
January 12, 2024
After gluing the bay for the main landing gear, I glued the upper wing sections to the bottom of the wings.
21
January 12, 2024
I glued the leading edges to the glued wings. Kitty Hawk has all the control surfaces in his kit as separate parts. This makes them easy to adjust to the desired position.
When the Gripen is on the ground, the leading edges are in neutral. So I didn't take advantage of the control surfaces deflection option in this case.
22
January 12, 2024
The kit contains a nicely crafted engine. After assembling the engine I painted only the inner surfaces. I did not paint the nicely rendered outer surfaces of the engine. It's unnecessary work. Once the hull is closed, the outer surfaces of the engine will not be visible.
I glued the assembled engine into the fuselage. Finally, I glued the fuselage halves together.
23
January 12, 2024
The kit contains a nicely crafted engine. After assembling the engine I painted only the inner surfaces. I did not paint the nicely rendered outer surfaces of the engine. It's unnecessary work. Once the hull is closed, the outer surfaces of the engine will not be visible.
I glued the assembled engine into the fuselage. Finally, I glued the fuselage halves together.
24
January 14, 2024
Comparing the rear of the fuselage with the photo, you can see that the front APU opening is too far forward on the model. It needs to be moved back 1 mm.
The rear APU opening is fine.
25
January 15, 2024
I moved the front hole of the APU back 1 mm and added details according to the photos.
26
January 15, 2024
I removed the poorly shaped air outlet on the right sideyr and made a new one out of brass pipe.
27
January 15, 2024
After finishing the modifications, I glued the prepared wings and nose to the rear of the fuselage.
28
January 15, 2024
After finishing the modifications, I glued the prepared wings and nose to the rear of the fuselage.
29
January 15, 2024
A joint photo of Italeri's single-seat Gripen with this two-seat version from Kitty Hawk.
30
January 23, 2024
I filled the small gaps between the glued parts with putty and after it hardened I sanded the joints with fine sandpaper.
31
January 23, 2024
I filled the small gaps between the glued parts with putty and after it hardened I sanded the joints with fine sandpaper.
32
January 23, 2024
The Gripen's instrument panel covers are covered with a padded "carpet". I marked its surface with thick paint, which I applied with a fine sponge .
33
January 23, 2024
I placed the instrument panels and pilot seats in the cockpits without gluing just for testing.

Kommentarer

20 10 December 2023, 23:06

Ludvík Kružík
During the construction of the single-seat Gripen, I got to the stage where I will seal and sand the surface of the aircraft several times. To take advantage of the time waiting for the sealant to set, I decided to start building a second Gripen. This one will be a two-seat "D" version. And the aircraft will be again with a special paint, this time for the 10th anniversary of Gripen operation in the Czech Air Force.
So I will alternate between building a single-seat and a two-seat version of Gripen according to the current status.

11 December 2023, 00:29

Sergej I
Great topic, looking forward to this adventure! 👍

11 December 2023, 18:49

Ludvík Kružík
Welcome, Sergei, I'm still putting together the construction documentation. But I'll start building the model soon.

11 December 2023, 19:33

J35J
I'm in! Taking a chair👍🏻

11 December 2023, 19:50

Ludvík Kružík
Welcome J35J!
The audience is gathering and I haven't started yet. I'll have to do something about that. 😉

12 December 2023, 13:19

Ludvík Kružík
I started construction today. I assembled both seats and started modifying the cockpit tub. I'll take some pictures tomorrow.

12 December 2023, 21:52

Ludvík Kružík
I'm continuing to build the cockpit.

13 December 2023, 21:03

Ludvík Kružík
The front part of the fuselage with the cockpits are almost assembled.

14 December 2023, 22:48

Ludvík Kružík
I'm gluing structural assemblies to the fuselage and wings.

9 January, 23:26

Ludvík Kružík
The main components (front fuselage with cockpit, rear fuselage with engine and wings) are assembled.
After the glue dries, I glue the assemblies together.

12 January, 22:51

Ludvík Kružík
The Kitty Haw kit also has its minor flaws.

14 January, 21:19

bughunter
Another interesting project from your bench! The tail painting is beautiful so this will be also a nice livre on the model 👍

14 January, 22:32

Ludvík Kružík
Bughunter, painting on the vertical tail surface was the reason I chose this machine.
Fortunately there are decals to paint the vertical tail surfaces. It would be difficult to create this paint at home.

15 January, 21:29

Ludvík Kružík
I glued the wings and nose with cockpits to the rear of the fuselage. Gripen looks like a plane now.

15 January, 21:52

Ludvík Kružík
I sanded the small gaps filled with putty. I'll fix a few minor mistakes and then spray Gripen with sufacer.

23 January, 23:36

Rando
A double delta build! I missed this. How is it putting together the Kitty Hawk? I've heard they're generally kind of notorious to put together. Although I think what would really keep me from building one is how ludicrously expensive they seem now that the company folded.

24 January, 00:05

Ludvík Kružík
Welcome, Rando!
Kitty Hawk is coming together pretty well. Compared to the Italeri kit, Kitty Hawk is much better to assemble. You can't avoid working with the putty, but it's not a tragedy. It's just minor gaps between some of the parts.

As for the high price of the kit, I got lucky and managed to buy the Gripen on sale for almost half the price.

24 January, 00:49

Project info

JAS-39D Czech Air Force

33 bilder

1:48

Påbegynt

1:48 Jas-39B/D Gripen (Kitty Hawk KH80118)

1:48 Decennial Gripen JAS 39D Czech Air Force (JBr Decals JBR48004)

Alle album

Se alle albumer »