modelarska baza danych | zarządzanie magazynem
Gidge
Gidge
AU

Red 5 X-Wing WIP

Komentarzy

22 19 May 2023, 06:53
Treehugger
Iirc the blaster cannons could use drilled out holes. Might be a little tricky if you aren't used to centering holes properly.

I just realized that I could try use a chrome pen for the R2D2 unit. Some things about using a chrome pen: Rubbs off at a touch of a finger, can be covered with a gloss coat to protect the chrome paint, can be removed with solvent if you aren't careful getting a fully covered surface. Can be difficult to apply on gray plastic because you can hardly see where the chrome is and where the remaining gray plastic is.
19 May 2023, 07:16
Gidge
The back of the blaster canons? Shouldn't be too hard with a hand drill, as there's a nice ridge. Though I'm not sure it's worth it in this scale. I had to take a close look at the reference photo to work out what you were talking about.

SMS make some ideal lacquer metalic paints for R2D2 that's pretty robust. Or are you talking about painting a blue undercoat on the dome, then applying the chrome and rubbing it off the raised sections afterwards?
19 May 2023, 08:28
Mr James
Watching with interest...
29 May 2023, 14:20
Jennifer Franklin
Following 👀
29 May 2023, 15:06
DerMattes
Following 👀
29 May 2023, 15:07
Finn
Will follow
30 May 2023, 19:04
Torsten
👀
11 June 2023, 11:29
Gidge
These decals are HORRIBLE!!!!
11 June 2023, 11:46
Dash Rendar
Oh damn, really? Are they broken easily or why?
11 June 2023, 15:51
Gidge
Just the opposite! Very stiff and rigid, wouldn't soften even with Mark Fit Strong! The carrier film was protruding over the edge of the surfaces and wouldn't bed down. I had to use Tamiya Extra Thin to soften them and make them conform.

I've had different reports from a friend who build the same kit, so your milage may vairy based on the batch.
12 June 2023, 11:24
Dash Rendar
Hmm interesting. I will try to keep this in mind. Hope you can still use them and bend them to your will. Heh.
12 June 2023, 11:44
Gidge
Based on this I plan on only using the decals in the cockpit. I'll mask and paint the exterior details. The only particularly challenging bit looks to be the unit markings but I've got the Green Strawberry masks for that.
12 June 2023, 11:54
Peter de Bruin
These kits have a set of decals and a ser of regular stickers. You sure you had the decals? I have this kit in the stash and the decals look fairly thin. Could of course be a batch thing as well.
12 June 2023, 11:56
Villiers de Vos
Very nice progress.
12 June 2023, 14:36
Gidge
Decals are fairly thin but super ridged. It's like they've tried to make them less fragile after complaints. Kit reviews have very inconsistent opinions of the decals so it's likely they vary greatly from batch to batch.

I tried the stickers for the helmet after stuffing a couple of the stripes (at least they give yous pares). The stickers for the helmet have fuzzy semi opaque clear boarders surrounding the Rebel insignia and the helmet stripe because they're so thin. Most of them do have no exterior clear boarder however. The stickers and decals have quite visibly different colours.

The decals are based on the studio models colour, NOT the way it appears on screen (they had substantial colour shift thanks to early blue screen tech) so that's one thing to keep in mind depending on what you're going for and how important accuracy is to you
13 June 2023, 00:08
Peter de Bruin
Thanks for the info. Will post my experience once I build it
13 June 2023, 05:49
Nicolas
Nice Build so far, joining in.
5 January, 13:52

Album info

Bandai 1:72 X-Wing, Luke Skywalker's Red 5 as seen in the original cut of Star Wars (later retitled Episode 4: A New Hope)

71 zdjęć/zdjęcia
1:72
W trakcie
1:72 X-Wing Starfighter (Bandai 0191406)1:72 T-65 X-Wing Paint Mask (Greenstrawberry AM011-1/72)

Wszystkie albumy

Wyświetl wszystkie albumy »