F-16CJ "Block 50" Tamiya FMM MdT
Komentarzy
61 11 February 2021, 16:16
Patrick Hagelstein
I see nothing but the highest quality stuff here, should build like a breeze. 😉
I see nothing but the highest quality stuff here, should build like a breeze. 😉
11 February 2021, 16:36
Treehugger
Do you get to have electrostatic wicks? Those thiny rods off the wings.
Do you get to have electrostatic wicks? Those thiny rods off the wings.
2 March 2021, 09:02
Mark D
Can you let know how the exhaust ring from Eduard matches the rear of the kit?
Can you let know how the exhaust ring from Eduard matches the rear of the kit?
2 March 2021, 09:45
Jorge Gallego-Madrid
Threehugger, no, I dont have the wicks, I will think later on the build how to do them...
Mark D, sure, I will dry fit the Eduard exhaust later this week and I can post here the result. I have heard that it does not match very well, but I already bought it :/
Threehugger, no, I dont have the wicks, I will think later on the build how to do them...
Mark D, sure, I will dry fit the Eduard exhaust later this week and I can post here the result. I have heard that it does not match very well, but I already bought it :/
2 March 2021, 13:17
Jos Jansen
That's a lot of AM stuff for this great Tamiya kit, looking forward to see all the progress pics...👍! Those electrostatic wicks called "Static Discharges"...great stuff from Master:
F-16 Fighting Falcon - Stati..ers (Master AM-48-112, 1:48)
That's a lot of AM stuff for this great Tamiya kit, looking forward to see all the progress pics...👍! Those electrostatic wicks called "Static Discharges"...great stuff from Master:
F-16 Fighting Falcon - Stati..ers (Master AM-48-112, 1:48)
2 March 2021, 15:32
Jorge Gallego-Madrid
It has been a crazy month at work, and I havent had so much time, but here are some progress 🙂
Jos, I think I am going to make the wicks with toothbrush fibers!
It has been a crazy month at work, and I havent had so much time, but here are some progress 🙂
Jos, I think I am going to make the wicks with toothbrush fibers!
13 April 2021, 12:34
Alexander
Nice range of aftermarket you got there, together with the selfmade wiring this should turn out really nice 👍 - awaiting further progress. 🙂
Nice range of aftermarket you got there, together with the selfmade wiring this should turn out really nice 👍 - awaiting further progress. 🙂
13 April 2021, 15:17
Patrick Hagelstein
After seeing your pictures I have to come back to my previous remarks: Yes, it should build like a breeze..........except that darn landing gear! 😄 (I included the Aires Wheel Bay set and forgot about this.....)
After seeing your pictures I have to come back to my previous remarks: Yes, it should build like a breeze..........except that darn landing gear! 😄 (I included the Aires Wheel Bay set and forgot about this.....)
21 April 2021, 13:58
Jorge Gallego-Madrid
Yep, that's right Patrick, the landing gear is coming up together nicely, but it consumes a loooot of time, luckily I am almost finished with all the photoetched parts 🙂
I considered using the Aires Wheel Bay set, maybe it would have been easier and faster, but I found the BIGED set relatively cheaper so...
Yep, that's right Patrick, the landing gear is coming up together nicely, but it consumes a loooot of time, luckily I am almost finished with all the photoetched parts 🙂
I considered using the Aires Wheel Bay set, maybe it would have been easier and faster, but I found the BIGED set relatively cheaper so...
22 April 2021, 08:20
Jorge Gallego-Madrid
Hi Sarunas, yes, I applied Mr Surfacer 1500 White over Eduard coloured photo-etch, as I thought it would be easier than paint everything and then glue the photoetched parts.
Hi Sarunas, yes, I applied Mr Surfacer 1500 White over Eduard coloured photo-etch, as I thought it would be easier than paint everything and then glue the photoetched parts.
3 May 2021, 09:38
Mark D
Nice progress! What I am not sure of is if this block version does have the newer aces II Seat with the stabilizers of the chute downwards at both sides of the headrest or still the earlier one? Maybe someone does know this? (I know the MLU has the newer version.)
Nice progress! What I am not sure of is if this block version does have the newer aces II Seat with the stabilizers of the chute downwards at both sides of the headrest or still the earlier one? Maybe someone does know this? (I know the MLU has the newer version.)
19 June 2021, 14:49
Mark D
To be more specific: they are the pitot tubes for the environmental sensor, that gives information to the recovery sequencer to determine which ejection mode should be activated at different speed/altitudes. (Thank you ejectionsite.com ?)
To be more specific: they are the pitot tubes for the environmental sensor, that gives information to the recovery sequencer to determine which ejection mode should be activated at different speed/altitudes. (Thank you ejectionsite.com ?)
20 June 2021, 14:32
Alexander
How did I miss the end of this build? Really great looking result, clean and professional! 👍 I also think that the exhaust looks very good too. 👍
How did I miss the end of this build? Really great looking result, clean and professional! 👍 I also think that the exhaust looks very good too. 👍
23 July 2021, 09:12
Slavo Hazucha
Oh wow, what a finish on this one!
Can't fail to mention the exhaust-job being a top notch affair, but man, the whole thing just looks great! I'm having my own fun with a grey-grey paintjob right now, and this is just a fine example how just shades of grey can look super cool & realistic without over-blasting the shading. Spot on 👍
Oh wow, what a finish on this one!
Can't fail to mention the exhaust-job being a top notch affair, but man, the whole thing just looks great! I'm having my own fun with a grey-grey paintjob right now, and this is just a fine example how just shades of grey can look super cool & realistic without over-blasting the shading. Spot on 👍
7 August 2021, 19:16
Jorge Gallego-Madrid
Thank you very much everyone 🙂
And thank you Slavo 🙂 I did the exhaust following the guidelines from Diejo Quijano's book "F-16 Aggressor"
Thank you very much everyone 🙂
And thank you Slavo 🙂 I did the exhaust following the guidelines from Diejo Quijano's book "F-16 Aggressor"
8 August 2021, 10:00
Grzegorz Janikowski
Beautiful.
I will be looking at your work, with my F-16 project. 😀
Beautiful.
I will be looking at your work, with my F-16 project. 😀
3 January 2023, 21:05