1/72 F4U-5 Corsair

1
October 8, 2019
Everything ready, let's give it a go, shall we?
2
October 8, 2019
One thing I did not mention is, that I decidet to replace the kit shallow "engine" with quickboost resin casting. Much more detailed and nicer
3
October 8, 2019
Some adjustement was required to fit the casting in the fuselage halves
4
October 8, 2019
quite a nice fit
5
October 8, 2019
To prevent the engine to slide inside the fuselage, plastic sheet glued in place to stop the unwanted movement
6
October 8, 2019
all parts ready for further painting and detailing (engine still need some love 🙂 )
7
October 8, 2019
Instrument panel sanded flat, painted white and then the thin foil was glued with the cover PE part (after spryaing it with tamyia XF-85 rubber black). Everything is glued together with PVA glue
8
October 8, 2019
Control stick and main cockpit painted.
9
October 8, 2019
this time, PE parts from the set were NOT used. (did not like them to be honest)
10
October 8, 2019
11
October 8, 2019
main cockpit is ready for installation
12
October 8, 2019
I will be adding some small parts to both halves of the fuselage. And after detailing the engine a little more, fuselage can be glued together.
13
October 10, 2019
Instrument panel and control stick glued in place.
14
October 10, 2019
and one picture with flash - just to see everything in there
15
October 10, 2019
control rods glued where they should be, painted and slightly weathered the whole engine
16
October 10, 2019
It's looking nice. I like it!
17
November 25, 2019
It's been a long time since uploading any progress.
18
November 25, 2019
wings and fuselage glued together - no major issues
19
November 25, 2019
small gaps between the upper transition between the wings and the fuselage - nothing major which a little bit of putty can't solve
20
November 25, 2019
aerials all prepared for the paintjob
21
November 25, 2019
small bits and bobs painted
22
November 25, 2019
main body finally painted with MRP colors
23
November 25, 2019
24
November 25, 2019
25
November 25, 2019
propeller central hup brush painted with Gunze metalizer
26
November 25, 2019
front top antiglare surfaces painted with MRP Super matt black
27
November 25, 2019
and gun barrels also brush painted with some Gunze Dark Iron buffable metalizer
28
November 25, 2019
Propeller ready for seal coat of varnish and weathering
29
November 25, 2019
All decals in place - now it's time for several coats of SOL to get rid of the few spots of silvering
30
November 25, 2019
31
December 13, 2019
After wash and small corrections for the chipping - plane is completed!
32
December 13, 2019
33
December 13, 2019
34
December 13, 2019
35
December 13, 2019
36
December 13, 2019
37
December 13, 2019
38
December 13, 2019
39
December 13, 2019
40
December 13, 2019
Nice kit, no major issues, few sink marks and small gap between the wing and the fuselage but otherwise very, very nice model. Highly recommended!

Komentarzy

Disabled

Album info

Another small 72 mojo build, just for fun.

The PE set is not correct for F4U-5 version (it should be for F4U-4). I know this and since I did not find the correct set for it, it will have to do. I'm not planning to use everything from the set anyway.)
And therefore do not expect " the right" look of the cockpit. 🙂

One other thing will be used - resin engine replacement.

1/72 F4U-5 Corsair

40 zdjęć/zdjęcia

1:72

Gotowe

Wszystkie albumy

Wyświetl wszystkie albumy »