Douglas X-3 Stiletto
Kommentarer
2 25 January 2016, 13:45
Hanno KleineckeThe visibility into the cockpit will be far better than I expected. The Pilot -seat combination in the kit is very little more than a lump of plastic, so I
tried to scratch something just to prevent the cockpit from being entirely empty.......
7 February 2016, 19:17
Hanno KleineckeSribing completed. The clear parts turned out to be unusably thick and too small. When I spoke to Bernhard about it, he suggested to replace them with very thin transparent foil, to glue them into place with CA and sand it flush. Turned out to be the perfect solution. Windows are completely flush with the fuselage now.
Many thanks to Bernhard Schrock !
10 February 2016, 20:36
Choppa Nuttaone sexy aeroplane ! very 1960's sci fi
and a cool project too Hanno
one to follow 🙂
10 February 2016, 20:39
Hanno KleineckeLol,I used Evergreen 0,13 mm Clear styrene sheet. 'Mon Cherie' wasn't on site. 🙂
10 February 2016, 20:59
Ben STONEHanno can you please explain to me the process of the clear parts and the "clear foil" used and what did you do when you mentioned that you sanded it flush? I understand the term but how did you go about it without affecting the clear parts?
11 February 2016, 06:54
Hanno KleineckeThank you Ulf !
@Ben : I cut two well oversized Parts out of 0.13 mm clear styrene, and glued them into position with Tamiya CA. After processeing, I sealed the seams with more Ca and sanded just the seams very very carefully, not to harm the see through areas. At first with a coarse sanding stick, then with 1000 grid Tamiya sanding sponge. Took me about 1,5 hours.
Next thing is to cut masks to protect the clear during the following steps. I hope to be able to close the fuselage today, after putting in the cockpit parts.....
11 February 2016, 07:10
Ben STONEDedication Hanno, thanks for the info. It's a lovely plane and one that I've wanted to do but unsure of which kit.
11 February 2016, 07:14
Hanno KleineckeAny time Ben. No shake and bake one available of this bird, I'm afraid. I came across this one by chance, otherwise I would have gone for the Planet kit I guess, but that one is rather expensive.There is another one from Mach 2, but everyone said it's crap. 🙂
11 February 2016, 07:35
Julian Herrero aka YuriI've got the MAch 2 and is really like a hard vacuform , may be worst ... Revell kit is not so bad .... I built it long time ago
[img1]
You've also got the 1/144 Dragon double kit which is shake and bake kit ....
11 February 2016, 07:41
Hanno KleineckeBeautiful build Julian ! 🙂 The Revell Kit really isn't bad fitwise, but the raised panels need some attention, the Windows as well, as mentioned. Wasn't aware of the Dragon one, but it´s not my scale anyhow.
11 February 2016, 08:04
Julian Herrero aka YuriThanks hanno .... As for the the windows I did otherwise....
I glued the kit clear parts and applied with several coats of Micro Kristal Klear until all was flush with the fuselage. After that a clear gloss top coat sealed it all. Not a perfect solution, but acceptable ....
11 February 2016, 08:39
Hanno KleineckeSome small progress : Scratchbuilt Cockpit parts attached to fuselage, masked the "windows". Ready to close the fuselage now.
14 February 2016, 20:02
Christian MeyerhoffExcellent start on this golden oldie! I´m pretty sure that You will make the most out of it!
14 February 2016, 20:10
Hanno KleineckeThanks Christian, the masking problem almost drove me nuts, but now I hope it will work...... 🙂
14 February 2016, 20:13
Bernhard SchrockSieht gut aus im Cockpit. Hast du Fotos von der Außenseite, maskiert? Bin neugierig, wieviel man von dem "Übergang" sieht🙂
15 February 2016, 05:18
Hanno KleineckeHabe ein klein wenig "Untermaßig" maskiert, um alles verschwinden zu lassen Bild 14. Der alte Record Kompressor hat für Belüftung beim Rumpf schluß gesorgt.... 🙂
15 February 2016, 05:31
Hanno KleineckeX-3 completed. This was no easy one, a lot of filling and sanding had to be done. Scribed some of the more important panel lines.
Decals were useless, as they were made in 1982, and everything White had turned yellowish. So insignias came from the spare box, and the logos were homemade.
Did a bit of scratchbuilt deatailing to the gearstruts and the inner side of the wheel well doors.
The highly polished looking Metal surfaces of the wings were done by using Uschi's
Chrome powder over Alclad Black gloss base.
13 March 2016, 20:44
Choppa NuttaI don't why but every time I see this model I singing "Captain Scarlet" 😄
still though, one very sexy build 👍 🙂
13 March 2016, 23:01
Hanno KleineckeThank you all mates, I'm proud you like It!
@ Choppa : You're right, its relation to the angel interceptor can't be denied !
14 March 2016, 08:53
Choppa Nuttaah Hanno ! of course !!
it was on the tip of my brain.... so to speak 🙂
14 March 2016, 10:22
Hanno KleineckeThank you Christian, you will be able to take a closer look at it in Lübeck. 🙂
25 March 2016, 16:35
Christian RistitsI love these experimental jets - very well done Hanno!
Seems the X-3 has similar wings as the F-104?
25 March 2016, 16:46
Hanno KleineckeThank you Christian ! You're right, apparently the F 104 was the main benefactor of the experience and data gained by the X 3 project. Their wings look very much alike !
25 March 2016, 17:52
Hanno KleineckeActually the X 3 never gained its full potential, as the designated Westinghouse J 46 engine never materialized, but the F 104 turned out to be the real hot rod 😎.
26 March 2016, 09:26
MRMLAVery nice result!!! 👍 When are You going to complete Douglas' lesser known high-speed research bird? 🙂
9 April 2016, 10:30
Hanno KleineckeLOL, thanks mate, I'm having some severe difficulties in scrounging up the specific kit 😄
9 April 2016, 19:30
