WIP - Sopwith Camel

1
December 1, 2021
White primer and a huge amount of tapes ...
2
December 1, 2021
Shading with thinned MRP NATO black
3
December 1, 2021
MRP linen color is on. But I need to replace it with a daylight picture!
4
December 1, 2021
The first thin layers of PC10.
5
December 2, 2021
In daylight the linen looks better.
6
December 2, 2021
I want to try the look of the blue, so I continued to work on the upper wing.
There is a white frame provided as decal, but with paint I can try to keep the shading. So masked all what is not white. I used MRP white. Insignia white or so looks better but the letters and fine symbols are white decals.
7
December 2, 2021
After inverse masking I brushed the blue (Gunze H15), which looks nice. Is with naked eye a bit darker.
Not perfect, but looks more like field modification 😉
8
December 6, 2021
I masked again the white and blue areas and the lower surfaces to paint PC10.
9
December 6, 2021
Why masking the lower surfaces?
10
December 6, 2021
Because the PC10 is sprayed around the edge.
11
December 7, 2021
The new Eduard 3D printed seats are fantastic! In black you can't see all the details.
12
December 7, 2021
Primed white.
13
December 7, 2021
Painted the first one with suggested paints.
14
December 7, 2021
For a second one on the right I used XF-55, then both with oils.
15
December 7, 2021
Both are finished with a darker oil wash.
16
December 9, 2021
In multiple masking sessions the ailerons are also done.
17
December 9, 2021
I started also to work on the fuselage internals.
18
December 9, 2021
I own also a PE set made by PART for the old Eduard Camel. As often there are crazy little things in this set! Here two straps (6 single parts).
19
December 9, 2021
I used the prepared straps to mount the fuel tank. Not sure about visibility later. The seat belts are Eduard Steel and are included with the 3D printed seat.
20
December 9, 2021
If the tank is in the back of the pilot he need to know about amount of fuel. So I created a fuel gauge according to my reference pictures. It is 0.6mm brass - thin like a bell wire! The 0.4mm inside diameter are filled with stretched sprue.
21
December 11, 2021
The last details are painted and rigging was added (0.1mm nickel silver and 0.3mm brass).
22
December 11, 2021
Some copper fuel lines and brass fittings.
23
December 11, 2021
All mounted into the right fuselage side. Please note the little protection on the wire crosses, made from thin paper.
24
December 11, 2021
Should be prominent when viewed from top, so it was worse the effort.
25
December 11, 2021
Tank and seat subassembly glued in place.
For the left side there is still something on the ToDo list.
26
December 11, 2021
The engine bearing is done, as a rotary needs to be able to rotate! Made some support from styrene.
27
December 11, 2021
Glued in place.
28
December 11, 2021
Thinned the front a bit for a deep fit as I need all the available space for the engine.
29
December 13, 2021
I realized that Capt. Hinchliffe need some fuel, so I painted the gauge more than half full (with Gunze Clear Green, hard to photograph).
30
December 13, 2021
A made also a main fuel shut valve ...
31
December 13, 2021
... and a fuel filter.
32
December 13, 2021
The PART PE sets contains always wonderful but crazy parts. I decided to use the throttle lever assembly and cut the Eduard parts away.
33
December 13, 2021
All mounted in the left frame. The frame is now on the fuselage halve.
After the picture I notice the loose rigging line - fixed, and added a rigging line on the upper corner as on other side.
34
December 13, 2021
Both sides together.
35
December 13, 2021
And finally the view from above.
36
December 14, 2021
Prepared the Brassin Vickers. The PE parts had a very tight fit on the resin barrel! Added pins for easier painting and later mounting.
37
December 14, 2021
Painted with airbrush Alcad Steel followed by a very light layer of Alclad Gun metal.
38
December 14, 2021
Painted leather and wooden handle with brush. Finally a very light dry brush.
39
December 14, 2021
Again on a dark background.
Will be mounted later on aircraft for easier paint job.
40
December 16, 2021
I tried at first on a lower surface of the aileron to peel the carrier film of the new style of Eduard decals (below). Decided to go that way. The upper one still has the carrier on top. I have left the overhang as starting point.
41
December 16, 2021
To handle decals with no backup is always a bit of thrill. To remove the carrier from this uneven surface even more!
42
December 16, 2021
Also the bigger part could be removed in one piece.
43
December 16, 2021
I really like the result! Here is clear coat Satin applied.
44
December 17, 2021
Many steps:
- cleaning parts
- white primer
- masking
- blue paint
- masking
- grey paint
- gloss coat
- poseidon decals
- removing carrier
- tyre decals (only now because of overlap of carrier otherwise)
- removing carrier
- flat coat
- painting of ropes anthracite
- painting hub metal
- add valves of 0.3mm lead wire
- add a spoke of 0.1mm nickel silver
- weathering will be done later
45
December 17, 2021
The backside is only blue.
46
December 17, 2021
The most beautiful wheels of my biplanes.
47
January 3, 2022
Löök is the Eduard name for a series of instrument panels in resin with print on it.
As mentioned before my parcel with the panel go strange ways and was send back by customs to the sender. I got my money back and ordered one in between, which arrived shortly before Christmas.
That is the content. Again with Steel belts, but the PE plate is different to the one of the wicker seat as here some wires for the IP are added.
48
January 3, 2022
The parts needs to be cut from the lower sprue and on the left part a cut out of the thin black middle foil is needed.
49
January 3, 2022
All is mounted together with some kit parts and the guns. But I had a massive problem with a dry fitting. I removed parts and it took a while until I realized, that the middle part with the instruments needs to be thinned heavily on the back, otherwise the gun part in the back of the panel sits is a wrong position. The mount of the Löök resin panel is different to the mount of a kit panel!
50
January 3, 2022
Now it fits. The protruding instruments are better than the 3D printed SPACE series or the kit's etched parts. But next time I will probably stick with the plastic of the kit.
51
January 3, 2022
During dry fitting I noticed another problem: The MGs protrude over the cowling! The resin barrel is a bit longer then the kit part. Not much, but enough to disturb a property of the Camel. Eduard says "Drop in replacement." No, fixed that too.
52
January 3, 2022
The tail skid is very thin! May be it is enough from the bench to the cabinet but I'm sure not for my transports. I managed also to break off the tail skid of the Fokker D.VII during the build, and that one was thicker. So better replace it now.
53
January 3, 2022
Some new parts from metal and wood. The upper part is a "shoe" made from very thin foil soldered to a 0.6mm brass profile. On the kit plastic PE should be added for control linkage, but I integrated that.
54
January 3, 2022
My new skid is may be not that correct, but much more robust.
55
January 3, 2022
The kit skid needs to added before closing the halves. I glued a piece of wire in to hold the suspension, so the rest of my creation could be mounted later.
The fuselage is closed now. On the fuel tank you may noticed the fuel filler cap. The two other caps are missing as I managed to break my last 0.8mm mill bit and the 1mm one is to big for the smaller caps 🙁 New ones are on the way.
56
January 4, 2022
The control stick would need some cleaning due to mould offset, but I soldered a new one, as on my other Sopwith aircrafts.
57
January 4, 2022
Goal was to show the upper open pipes.
58
January 4, 2022
Here mounted on the front part of the fuselage with rudder bar and some control wires.
59
January 4, 2022
The front part was snapped in (the fit is impressive!) and fix with some glue. The back parts of the Vickers are also mounted.
What a busy cockpit!
60
January 4, 2022
The cockpit cover is only dry fitted, need some work.
61
January 4, 2022
With the naked eye some details of the cockpit are visible.
62
January 5, 2022
Today I got a belated Christmas present from my wife - Rudi Rednose's sledge was stuck in a traffic jam 😉 Not exactly this Camel, but very nice!
63
January 8, 2022
As I mentioned I had to order new micro mills. After they arrived I turned the two remaining smaller filler caps to 1.2mm and milled them with a 0.6mm mill.
That are wonderful two knife edge mill bits for alu and brass!
64
January 8, 2022
Looks nice in the cut outs of the upper decking. You can also see my sanded cowling.
65
January 8, 2022
Now some words about the cowling.
May be you remember the older Eduard kits? If there was a cutout in a cowling you got two parts. Now it is different!
The sprue D is not in a great quality as the other 3 sprues and the reason seems to be that Eduard is using here a slide moulding technology. On the picture you see how it works, two mould halves and pins from the side in the middle for the cutout. This seems to cause a seam, which needs to be removed.
66
January 8, 2022
Eduard had a problem with this (new?) process, so you can notice here an incomplete front ring of the left.
67
January 8, 2022
I solved this problem with adding a front ring from the Parts Camel set. Not very sharp etched rivets, but a improvement for sure.
68
January 8, 2022
I painted also the struts, which have nice mount points, but are very thin. I do not like at the end my wood painting and my wife asked: "Why no wooden struts this time?" So I have now a bunch of nice little but rigid wooden sticks.
69
January 10, 2022
The kit offers 4 engine types: Clerget, Gnome, Le Rhone and the Bentley, which I need in this build. That are the parts.
70
January 10, 2022
Plugged together - not that bad, but I don't like the 0.63mm "pipes" at the front!
71
January 10, 2022
The Bentley B.R.1 (also the B.R.2) are not available by Small Stuff. But there is one available from Eduard for this Camel in the new Brassin Print series.
I a sturdy cardbox you will a manual, a little PE plate and two black resin parts (in the middle).
72
January 10, 2022
That are the engine parts alone out of the box, directly printed in a very hard resin (no comparison to the gray cast one).
73
January 10, 2022
On the back you can see the print supports, which needs to be removed carefully.
74
January 10, 2022
After cleaning and modification of the parts (I drilled a 1mm hole for my axle - needs to be centered!) plugged together with the PE parts in between. That was not easy, as I need to remove more than the supports, otherwise the intake pipes do not fit to the cylinder heads!
75
January 10, 2022
Here the front. You see, that the push rods are printed with the engine and much thinner compared to the kit part. But you can see also, that this little beast rolled from my bench after my modifications were done and lost one valve rocker and some push rods!
76
January 10, 2022
But beside this mishap the engine fits on the axle.
77
January 10, 2022
After thinning the cowling on the inside a bit the Bentley is able to rotate freely and smoothly.
78
January 10, 2022
But what to do now?
If you look for references (what I usually always do - this is a fun part of the hobby) you will need also to look for Bentley A.R.1 for "Admirality Rotary", which was later renamed to "Bentley Rotary". The engine was developed as a less troublesome replacement for the Clerget.
On Wikipedia you can find this wonderful picture, also in a high resolution.
79
January 10, 2022
The push rod looks still thick with 0.3mm on the printed engine. I know, that the resin push rods of the Small Stuff engines are 0.15mm, also on the Clerget. So I measured them on the high resolution pictures: yes, exactly that size also on the Bentley!
So I removed also the remaining push rods, painted the engine with Alclads and add new push rods from 0.15mm wire.
80
January 10, 2022
After mounting the parts together I added ignition wires (wanted to use Small Stuff spark plugs, but no chance to drill in this hard resin so I faked some). Same copper wires as I use on Small Stuff because I found the provided PE to thick.
Finally a light oil wash.
81
January 10, 2022
A view onto the cylinders.
82
January 10, 2022
And from back. This is visible if you look through the big cutout of the cowling. I was not able to get better sprue gates.
83
January 10, 2022
Even if I prefer a Small Stuff engine I'm very happy with my first Bentley B.R.1 !
84
January 13, 2022
The kit contain a clear plastic part and a mask but I find those parts always to thick.
There is a PE frame and printed acetate sheet in the Part set. So I soldered the two parts.
85
January 13, 2022
Cut out the foil and glued it to the back side of the frame.
86
January 13, 2022
The manual required wood paint inside the cover, but I painted the front alu.
87
January 13, 2022
Due to a more complicated masking I decided to paint also blue and leather now.
88
January 13, 2022
Cover is glued in place and masked completely.
89
January 13, 2022
Fuselage primed white.
90
January 13, 2022
Masking - shading.
91
January 13, 2022
Masking - linen paint.
92
January 13, 2022
Masking - PC10.
93
January 13, 2022
Masking - white
94
January 13, 2022
Until now all was ok.
And now the a lot of masking again.
95
January 13, 2022
96
January 13, 2022
And finally the blue paint.
97
January 13, 2022
That was not a 100% success ...
98
January 18, 2022
I squeezed 1.3mm brass to a airfoil shape.
99
January 18, 2022
That are the basic parts of a new undercarriage, build from 28 brass parts and 3 layers of veneer.
100
January 18, 2022
In the profile view you can see the "rolls" to wind in the suspension later.
101
January 18, 2022
Plugged together. Here is also this typical half axle made of 1mm nickel silver added. It has a hole already to be pinned in the middle.
BTW the kit axles was also 1mm, but the holes in the wheels a little bit bigger. I hate, if the wheels are not straight later, so I added 1.2mm brass bushes into the wheels.
102
January 18, 2022
It fits to the fuselage, here fully deflected.
103
January 18, 2022
And in neutral position.
104
January 20, 2022
The limiter of the suspension rubber lines are soldered to the half axles. Please note also the 0.32mm holes, which are later the rotation points.
105
January 20, 2022
All parts are finalized and the legs and the wooden axle holder are glued together.
Brass color is gone. Primed with Mr. Metal Primer.
106
January 20, 2022
Final dry fitting before painting. The axles are only plugged in.
The color was a question for me. Eduard says grey, but I followed here the WNW manual: blue.
107
January 20, 2022
The gear was painted. I masked the wooden board a bit on lower side, as wet grass and little stone has removed the paint there.
After drying I mounted the axles with 0.33mm nickel silver. That "bolts" are secured with little plates on the front, with additional 0.2mm bolts. The "rubber" lines made from stretched sprue are also wound in to hold the axles and later the model.
108
January 20, 2022
The undercarriage is now mounted to the fuselage. I drilled out the brass bushes in the wheels slightly, so the wheels are now very close to the suspension. It matches the drawings.
109
January 20, 2022
And in a side view. The wheels are not yet fixed to the axles.
110
January 21, 2022
The decals provided by Eduard are very nice, here the fuel cap lettering.
Can't read it with naked eye, but the text is "PETROL GRAVITY"...
111
January 21, 2022
... and "PETROL PRESSURE".
112
January 21, 2022
My plan was to remove the carrier film, so I take care that there are no overlaps and applied the decals in multiple sessions (carrier removed after 10 hours).
113
January 21, 2022
Even the stitching was no problem!
114
January 21, 2022
That is the result - no carrier film visible
115
January 21, 2022
After the decals I mounted the engine, the cowling is also finally in place. On the cowling front a little brass plate is added. It was part of the ring, but I cut it to keep it in brass.
The cowling is also secured with a rope and 4 securing plates with wing nuts (no, it is still no Wingnut kit 😉 ) from the Part set.
116
January 21, 2022
The removed kit "locks" are now replaced by brass locks. Albion Alloy offers now also aluminum micro tubes, which I used for intake pipes.
117
January 21, 2022
On the backward side of the metal panel was also a securing rope. The kit fuselage already had a recess here so I drilled holes and added a wire.
118
January 21, 2022
This is now the actual state, right side:
119
January 21, 2022
Left side:
120
January 21, 2022
And from top, with the fuel caps. The sign on the back looks a bit different on the WNW kit, but I have no chance to change this.
121
January 22, 2022
A Rotherham air pump was used to put the fuel system under pressure during flight. There were different locations of the pump, on upper strut or on undercarriage leg.
Due to different struts and undercarriages Eduard respected that and offers here different parts with the pump. There are another parts without the pumps, so you dont need to remove the pump in the other cases.
This limited Edition kit provides even PE parts for the mounts (see 11 and 12) and a prop (17).
122
January 22, 2022
But I will not use all those parts!
Eduard wouldn't be Eduard if they didn't go a bit further: There is another Brassin PRINT set for the Rotherham air pump!
123
January 22, 2022
You will get five different mounts (two of each type) as PE and some 3D printed parts in black resin.
124
January 22, 2022
Here a more bright picture, which shows three different props and three air pumps of 2 types.
125
January 22, 2022
I could see the pump well on the original photo, so I selected the matching parts, painted and mounted them.
126
January 25, 2022
The kit wings has some special shaped holes (different sizes on upper and lower wing) for the mounting of the struts. But this makes it harder to add pinned wooden struts.
127
January 25, 2022
In real you see some black metal socket between struts and wing. So I tried to use black sprue to fill the wing hole and mount the struts. But it fails, takes to long to made them, the 0.4mm pins break this plastic and it do not hold the struts well. So I need to think about another solution.
128
January 25, 2022
In meantime I solved the inspection window problem. Would be better to do it at first, but I ignored it at the beginning.
- Painted with wood, linen, alu and black.
- The inspection windows of the PART kit, which I wanted to use, cannot be used, as the recess in the kit wing is the same size.
- So I used the clear kit parts, but removed the moulded frame on top and polished them again.
- clear parts glued in with "Kristal Klear".
- PE frames from PART set added on top.
129
January 25, 2022
In the bigger middle window of the upper wing I had to cut the frame as it was too wide.
130
January 26, 2022
I found a solution for the strut mounts: I squeezed pieces of 1.0 and 0.8mm brass tubes with thicker wall of 0.2mm and glued them into the wings.
The opening in the upper wing was also painted to look like wood.
131
January 26, 2022
Same for the outer struts, here I added also thin brass wire as pins to the ailerons.
132
January 26, 2022
Since I was in "pinning mode", I also added pins to the tail pieces.
133
January 26, 2022
I masked the windows and added clear coat to the whole wing, which is now ready for mounting.
134
January 26, 2022
Here the "wood" from the top side. If you look carefully you can notice the first four rigging wires.
135
January 26, 2022
The inner struts are glued to the fuselage (the wing helps for positioning), then I glued the prepared wind shield in place.
136
January 26, 2022
The upper wing was added to the struts.
137
January 26, 2022
The next task was to start the rigging, at first the inner crosses. RAF wires was used on the Camel so NO turnbuckles! The terminals are made by Gaspatch.
138
January 26, 2022
For the main rigging I want to use the more flat and bigger EZ-line, but it is very hard to get it through the terminals!
139
January 26, 2022
Lower wings added, outer struts are in place and the landing wires, again RAF wires, are done.
140
January 26, 2022
A view from back. Here you can see also the metal plates from the PART set, which are added as step plate.
141
January 26, 2022
I tried to avoid twisting of the EZ-line.
142
January 26, 2022
The rigging in detail. The "fork" of the terminals will be painted black, the RAF wire metal.
143
January 26, 2022
I mounted also the prepared tail skid, the inner "suspension" is a metal wire able to hold the weight of the model.
144
January 26, 2022
And now a teaser in the last day light with wheels - it starts to look like a Camel!
145
January 26, 2022
Later I added the Clayton manufacturer logos on the struts, so that I can remove the carrier film tomorrow.
146
January 28, 2022
I continued with the double flying wires.
147
January 28, 2022
Here you can see the double wires, the undercarriage rigging including a normal turnbuckle in front of the wooden axle board. Also the lower maintenance panel has fasteners.
148
January 28, 2022
I forgot to mention this, I made a breakthrough in the lower wing, here in comparison to the wing of the second kit.
149
January 28, 2022
The double RAF wires looks nice.
150
January 28, 2022
And now the most crazy part I have ever done!
Two wooden cones, on a 0,3 nickel silver and 0.5 brass pipe "axle", with cuts in one of them to add nickel silver pipes. It can slide on some ropes. I guess you Camel experts know, what it is?
151
January 28, 2022
And mounted! The overall length is 4mm. After that I added also the MGs.
152
January 28, 2022
It is also visible from top.
153
January 28, 2022
And because it is so nice also in side view.
154
January 28, 2022
The crosses between the struts are also applied and the carrier film on the logos is removed.
155
January 28, 2022
And now a final teaser of the actual state. Here you can see the single turnbuckle clearly.
156
February 1, 2022
On the rudder the decals are applied, I had to paint the edges and found luckily matching paints in my stash (Gunze H33 and H322).
157
February 1, 2022
For the control horns I do not used the Eduard PE, but again the PART set.
To get a more realistic look I made the horns thicker with tin. On the right you see the aileron horns. Each type has a different size.
On the left you see the horns of the rudder. I added a 0.33mm nickel silver bolt and a slotted metal as hinge, to realize the double wire control as shown on my linked high res pictures.
158
February 1, 2022
For the mounting I started with the control wires to the skid, added then the tail plane. After the control wires ...
159
February 1, 2022
I added also the rigging. I used turnbuckles according to the mentioned pics, but that was not necessary. Later I checked old b/w pics - there were no turnbuckles. I let them there, it is a nice detail.
160
February 1, 2022
After clear coat on the rudder I added the control horns and the wires. Looks not nice, but it is easier to do outside.
161
February 1, 2022
After mounting the control wires are connected.
162
February 1, 2022
The completed tail, only some detail painting and touch-up are missing.
163
February 2, 2022
The Eduard kit pitot tube, and my own creation. I used some PART PE, but removed the etched flat "pipes" and soldered 0.3mm nickel silver micro tube and a wire which I sanded to a cone at the front, between the holders.
164
February 2, 2022
Painted black and mounted with 0.2mm lead wire as pipes. The pipes run into the upper wing with black rubber coupling, I guess to be able to remove the wing.
165
February 2, 2022
The pipes run inside the wing to the inner strut and again via rubber couplings into the cockpit.
166
February 2, 2022
On the lower wings I added two rings with a mounting stripe. I think they are used to secure the Camel on ground.
167
February 2, 2022
The ailerons are also added, including the control wires.
168
February 2, 2022
The prepared Rotherham air pump was glued to the gear leg. A thin copper wire passes the compressed air into the fuselage.
169
February 2, 2022
After adding the wheels he last step was a light weathering with different methods.
Sorry, this pictures are not perfect.
170
February 2, 2022
171
February 2, 2022
172
February 4, 2022
Now the airscrew.
There are 4 little white stripes in the kit as decal, but they are not long enough to go around. I assumed complete white rings. So I decided to mask and paint the airscrew. My first paint job failed. Finally I removed the paints completely and start from fresh. The type description is a nice detail, a decal of this kit.

Comments

79 1 December 2021, 20:27

Robert Podkoński
Watching with pleasure, of course! 🙂

1 December 2021, 21:34

Marcel Klemmer
I will take a seat….

1 December 2021, 21:44

Christoph Kunz
I'm in too

1 December 2021, 22:01

Juergen Klinglhuber
The fans are gathering.....👍.

2 December 2021, 06:51

Michael Kohl
I grab a seat too...

2 December 2021, 13:53

bughunter
Welcome to the show mates!
But I have to admit that there won't be as many scratch parts as in the last project.

2 December 2021, 14:48

bughunter
New pictures. Need to wait now for drying, then mask again and paint the outer parts of the wing late PC10 (this is a special British green mixture).

2 December 2021, 14:56

David Taylor
Off we go again.

2 December 2021, 15:36

Giannis Kaltapanidis
Definitely in!

2 December 2021, 16:11

Alec K
"Mostly OOB" he says… 😄 😄 😉

4 December 2021, 12:50

Robert Podkoński
... and perhaps for Bughunter this is a kinda leisure build 😉

4 December 2021, 15:00

David Taylor
OOB Hmmmm.lol

4 December 2021, 17:53

bughunter
Welcome and thank you for your interest! 👍
Ok, regarding oob - I plan to include some of the Eduard accessories. But ...
Now I realized, that the struts (0.7mm) and the undercarriage (0,6mm) are very flexible! 🙁 It is may be strong enough to put it from the bench to the cabinet but I have (strong) doubts about transport to exhibitions. And nothing is more frustrating than transport damage to a finished model (I've known this since a broken landing gear on my Nieuport 11). Let's see ...

6 December 2021, 16:27

Christoph Kunz
Stay safe, show us some brass. 😉

6 December 2021, 19:38

Juergen Klinglhuber
Sometimes I get the feeling that I can't trust my eyes. Great accuracy & detail.
Not only the chairs are looking great 😉
👍

7 December 2021, 20:37

Bernhard Schrock
Hast Ameisen eingestellt, die dir die Sitze geflochten haben wa? 🙂 genialer Effekt! Wie ist es gemacht? 3D?

7 December 2021, 20:41

bughunter
Yes, see comment below pic 11 and project inventory. This is 648659 of the new "Brassin Print" line. The parts are directly printed in black resin. Sopwith Camel seat (Eduard 648659, 1:48)
The Camel kit and it's accessories are impressive!

7 December 2021, 22:16

Ben M
Bughunter's next build will feature seats woven from real dwarf rattan 🙂

9 December 2021, 17:16

bughunter
Welcome to the Camel build Ben!
I started to work on the fuselage, but I'm still waiting for my Löök set! The parcel was one month in the Europe post offices, because it was misrouted to UK. They noted this and send it back to Germany. But if something coming from UK is reaches the customs office in Germany at first. And finally after a month it was sent back to sender because tax declaration is missing. 🙁 Of course there was no declaration for a packet within Europe! So brain dead. The hotlines are useless too, because they cannot clear a situation like this.

9 December 2021, 17:28

Pepe
😳😳😳😳😳😲

9 December 2021, 18:13

Björn Svedberg
I can't miss this! 🙂. Love your work! 👍

11 December 2021, 09:49

bughunter
Thank you mates fro comments and likes!
Nice to see you again Björn!

11 December 2021, 15:39

Pierre Pierre
following

12 December 2021, 13:33

gorby
I knew you wouldn't be able to do an OOB build Frank, and it's all the better for the Bughunter touch.

12 December 2021, 15:03

bughunter
Thx and also a warm welcome to the new guests!
Pierre, you are following Modellversium? Then you may be know already my style of modeling 😉
gorby, to use PE sets and available add-ons are oob for me 😉 So I added only some wires here.

12 December 2021, 16:42

Michael Kohl
Great internals. OOB, ofcourse. 😉

12 December 2021, 19:03

bughunter
Thx! With the help of the wonderful drawings in the Windsock Datafile and high res pics of a flying Camel in New Zealand I added all those fuel line on the left side. Now I understand this system. Before anyone asks: Of course it's fully functional 😉

13 December 2021, 17:08

David Taylor
Will you be using castor oil for the engine.

13 December 2021, 17:30

bughunter
I'm afraid I'd get in trouble with the head of the household because of the smell.

13 December 2021, 18:24

Pepe
Incredible

13 December 2021, 19:25

Alec K
Those fuel lines and associated valves are just amazing.

13 December 2021, 23:32

Spanjaard
amazing details on all those fuel pumps, levers and so on... fantastic.

14 December 2021, 00:50

bughunter
Thank you very much mates!
The hump that gave the Camel its name covers the rear part of the Vickers MGs, the front part is on top. Yes, there are also nice Vickers from Gaspatch, but the split ones from Eduard makes painting easier. Unfortunately, the barrel is not so nicely open at the front.

One of the next tasks is to try the new Eduard decals. Never made that experience! I do not like the heavy carrier film and will try to remove it.

14 December 2021, 16:37

bughunter
Wow! After trying the new decal style on a lower surface I decided to peel - looks fantastic 👍 Thank you Eduard!

15 December 2021, 07:43

James C
Impressive detailing again mate 👍

16 December 2021, 16:12

bughunter
To peel or not to peel, that is the question! I decided to peel 😉 The result is fantastic 👍
One should decide before apply the decals: If you want to peel I would left the huge carrier as handle. If you don't want to peel I would cut out the decals right to the edge.

16 December 2021, 16:19

Robin (WhiteGlint)
Amazing work 👍

16 December 2021, 17:17

Lochsa River
Checking this one out.....every build is an inspiration

16 December 2021, 17:22

bughunter
Thank you mates!
@James: sorry, have not noticed you post, because I was already editing my post. Need to ask Tim about this.
@Lochsa River regarding the inspiration, I found a new motto:
Build each model in such a way that the previous one becomes envious. 😉

16 December 2021, 18:32

Erik
Really looks like lacquered. 👍

16 December 2021, 18:36

Alec K
Indeed, those new decals look interesting.

16 December 2021, 18:51

bughunter
Some remarks: The new style decals are in all kits since a year or so. Eduard never states in the manuals or so about the possibility to peel, because the fear to be responsible for problems (see Editorial of Info 4/21), but there was a HowTo and comparison in Eduard-Info 5/21 from page 52, which I strictly followed.
Another advantage is a easy weathering after carrier is removed.
I wonder, that no one mentioned this here, or may be I have not noticed. Some people seems to hate this new style. There are videos on YT doing strange things on them, don't try to follow that way!

16 December 2021, 20:12

Alec K
I now actually recall reading about that in the Eduard newsletter. Glad you showed us how. It certainly looks painted on your model 👍

17 December 2021, 00:41

Predrag Ivanovic
Great progress,as always a lot of your own improvеments and thats wonderful. I build exactly the same Camel at the moment .

17 December 2021, 06:30

bughunter
Thx Pedja and Welcome to the show here too 👍

17 December 2021, 07:06

bughunter
I own also resin wheels, but I used the kit provided ones as they look closer to the original pic on this specific Camel.
Due to the drying times it took a while with that many steps!

17 December 2021, 15:07

bughunter
After a break due to Christmas, we are now moving on.

3 January 2022, 20:20

gorby
Your attention to detail is phenomenal.
I hope you had an excellent Christmas Frank, and that your new year is a damn sight better than the rubbish ones we've been having recently.

4 January 2022, 08:42

bughunter
Thank you gorby for your continued support 👍 And also for you and your family and allthe other mates here a happy and successful 2022!
I hope to finish more models in the new year as in the last one. 2021 only 4 models are finished, but the Mirage kit and 3 resin models costs more effort and time.

4 January 2022, 15:53

Urban Gardini
How have I missed this one? Must follow along!

4 January 2022, 18:50

bughunter
Welcome Urban! Just added some pictures of the fuselage front which is glued into the front now.

4 January 2022, 18:52

Jennifer Nijhuis
Those details in the cockpit O_O It's really astonishing. I will follow along

4 January 2022, 20:34

Michael Osadciw
Looks amazing? I'm curious, what is that wide white and red fabric bit draped across the seat? I think it was in one of your Eduard sets. Is it a signal flag or something?

4 January 2022, 21:37

bughunter
That is no flag, it is the seat belt 😉
The Sopwith do not use 4 belts as the Germans (shoulder and pelvis) but only a wider pelvis belt, but with 3 securing pins. I used here the Eduard Steel belt as provided with the seat, see also picture 19 of this album.
Sopwith Camel seat (Eduard 648659, 1:48)
Another option would be the HGW belts made from some kind of fabric. I used it on my Sopwith Dolphin, see here and the next picture:
WIP - Sopwith 5F.1 Dolphin | Album by bughunter (1:48)

4 January 2022, 21:54

Michael Osadciw
Thanks! I'm not familiar with WWI planes so that was interesting!

5 January 2022, 13:19

Robert Podkoński
I hope you all, Mates, have noticed or rememeber that Bughunter described this build as "mostly OOB" 😉... How should I call my builds, as up to now I considered them as mostly OOB... 😭

5 January 2022, 14:56

Urban Gardini
"Mostly OOB" - Bughunter is slightly comparable to when David Damek (PLASMO) says that he'll do some minor scratch building...

5 January 2022, 18:47

bughunter
Mates, you made my day! OOB includes all the aftermarket sets 😉
Today I got a belated Christmas present from my wife - Rudi Rednose's sledge was stuck in a traffic jam. See picture 62.

5 January 2022, 20:36

Ben M
That's very thoughtful of her!

5 January 2022, 22:43

Alec K
Very nice gift 👍

6 January 2022, 01:31

bughunter
Thanks mates, I will pass it on!

7 January 2022, 13:30

Robin (WhiteGlint)
The engine's pretty impressive. 👍

10 January 2022, 20:01

bughunter
This time again my special method - improvement due to an accident! A big update with many pictures and a lot of work!
That picture was somehow my template: [img1]?format=1000w

10 January 2022, 20:03

Hanno Kleinecke
What a beautiful engine, superb work !

10 January 2022, 20:38

Robert Podkoński
Looks absolutely realistic. Fantastic work!

11 January 2022, 06:10

Michael Kohl
Good decision to change the push rods. This makes all the difference. Now this engine is a real gem.

11 January 2022, 07:12

Alec K
That engine could be displayed by itself 👍

11 January 2022, 14:57

Dietmar Bogatzki
Beatifull Engine 👍

11 January 2022, 16:43

Robert Podkoński
I do agree with Alec K here! Maybe you will consider displaying the engine separately next to the finished kit, Bughunter?

11 January 2022, 16:45

Phil Paradis
Excellent!

11 January 2022, 16:57

bughunter
Thank you very much mates!
This engine will be mounted definitely in this Camel! The good thing is, that the cowling is wide open and shows a lot. Even the back side is visible from below due to the cutout in cowling and recess in the fuselage.
But I have a second printed Bentley in my stash. Not sure about the marking of the second Camel of this kit, so which of the 4 engine types is needed? This follows much later.
Alec and Robert, I really think about a row of engines to show alone or next to the plane, presented like this Benz Bz.IV: Benz Bz.IV | Album by bughunter (1:48)
I have all of the Small Stuff tyes in my stash 😉

11 January 2022, 18:05

Alec K
Great idea. Like in a legit museum 👍 🙂

11 January 2022, 19:42

bughunter
After multiple cycles of masking and painting the project has made a little step progress.

13 January 2022, 18:36

David Taylor
Very smart paint job.

13 January 2022, 19:46

bughunter
Thank you David!
I mentioned above the flexible landing gear legs and Christoph replied "Show us some brass." So we know, who is responsible.

I need to mention it: there are more the one variant of a Camel undercarriage, a check of references is needed! For my Camel I found wonderful reference pictures:
[img1]
[img2]

That was a lot of work, but now it is very robust. And now it is more compatible to the other Sopwith, since also my Pub, Dolphin and Triplane are equipped with brass undercarriages.
A cleanup and more work on the axles is needed now.

18 January 2022, 19:09

Christoph Kunz
This time I'm proud to be guilty 😄

18 January 2022, 19:15

Dietmar Bogatzki
Great job, nice detailing and great paintjob 👍

19 January 2022, 07:24

Greg Baker
Sign me up for another jaw dropping bugsy build…

19 January 2022, 07:25

Michael Kohl
bughunter, again a build log giving inspiration and motivation to try out new techniques. Question: how do you fashion the main struts? Do you squeeze round brass profiles into oval shape or round square ones, or any other technique?

19 January 2022, 08:39

bughunter
Thank you mates!
Michael, the legs are squeezed micro brass tubing (available in many model shops from Albion Alloys from 0.3 to 2.0mm in 0.1mm steps).
I'm now applying the next batch of decals ...

19 January 2022, 18:56

Hanno Kleinecke
Once again I'm totally flattened by what you are able to create with wood, metal and a soldering iron, very inspiring 👍.
Love the blue and white livery !

20 January 2022, 19:24

bughunter
Hanno, just as flattened as my Albion Alloy brass tubes? 😄 😄 😄 Sorry, the pun was obvious!
Thanks Hanno, yes that blue and white looks great. Unfortunately the masking was not perfect, that would have looked even better. I also had a matching light blue from Drooling Bulldog, but I didn't think of that at the beginning.
Maybe you can see the beast live soon?

20 January 2022, 20:43

bughunter
The decal on the fuselage are done, in multiple session to avoid a overlap.
The possibility to peel the carrier off is great, especially for stencils and holes (like the fuel caps here).

21 January 2022, 18:17

Juergen Klinglhuber
amazing - no words --> just 👍

21 January 2022, 18:24

Hanno Kleinecke
Of course I would appreciate seeing this gem live,
do you plan on attending an exhibition ?

21 January 2022, 20:04

bughunter
I have never visited the exhibition in Lingen, but despite the long journey, there are things you should do at least once in your life.
But I fear that it will fall victim to the virus this year too?

22 January 2022, 12:29

Hanno Kleinecke
It most probably will, I'm afraid......... I took part there once and I must say that the dimension of it was really impressive. But generally I'm somewhat uneasy with exhibitions, and like you mentioned - it is quite a distance, from where I live as well, so I never repeated it.

22 January 2022, 12:46

bughunter
Today nothing scratched, just an out-of-the-box build!
I will mount the pump on the undercarriage leg later, because I am afraid of damaging it while handling the model.

That is a nice piece of accessory (impressive use of 3D printing), which allows more then one pump. The detail is by far better than what is included in the WNW kit, despite the smaller scale.

22 January 2022, 16:21

Rui S
Looking ... As always 👍
I'm 😎

22 January 2022, 17:36

Michael Kohl
Further amazing progress. I am surprised how easy you seem to be able to peel off the decals carrier film. I really had difficulties with this. Do you see a difference whether you apply the decals onto a gloss paint or a flat one? I found it easier to start the peel if I cut the thin edges of the decal. You experiences would be appreciated.

22 January 2022, 18:22

bughunter
Thank you mates!
Michael, I followed strictly the recommendation in Eduard Info journal May 2021.
Applied on glossy clear coat, used water and added blue cap Gunze Setter as recommend. Decals pressed down and all water removed with Qtip. Peeled of the film after 10h and was surprised how easy this was. It was easier on the decals near a corner, here I could grab the carrier with little tweezers. On a plain surface I put a wooden tooth stick to a corner until it lifts up a bit and then removed it with tweezers carefully.

22 January 2022, 18:41

gorby
Photo No. 125 of the air pump is remarkable!

23 January 2022, 07:42

Spanjaard
Fully agree with gorby

23 January 2022, 09:23

bughunter
Thank you my friends!
Ok, if you like that picture so much: 125 is now the actual teaser 😉

23 January 2022, 15:56

Spanjaard
👍

23 January 2022, 18:17

Greg Baker
I've given up trying to express my feelings about Bugsy's projects… I'll just continue to stand in silent awe and will notify you if anything changes…

24 January 2022, 07:03

bughunter
Greg, good to know that you found this build in this flood of great models 👍
To avoid making this look too easy, I will show a failed attempt soon.

24 January 2022, 16:03

Greg Baker
From someone else? I can provide you with many examples from my project list... 😉

24 January 2022, 17:56

Ben M
it is a bit surprising the fuel system isn't actually functional, isn't it, Greg 🙂

25 January 2022, 00:00

Greg Baker
I'd have thought my disappointment would be obvious... 😄

25 January 2022, 03:53

bughunter
You are so wonderful mates!
The strut mounts failed, but the inspection windows for the aileron pulleys are done.

25 January 2022, 20:51

Dietmar Bogatzki
and what a great job on the inspection windows 👍

26 January 2022, 06:31

Erik
Deine extrem saubere Arbeit lässt mich immer wieder staunen. Gerade jetzt, wo ich gestern erst wieder was versaubeutelt habe...

26 January 2022, 07:57

bughunter
Thank you mates!
I think I can post new pics soon as it is a biplane now 😉

26 January 2022, 14:12

bughunter
Now it is a biplane 👍 I really like the look of this Camel!
But there is still a lot of work on the ToDo list ...

26 January 2022, 17:27

Michael Kohl
Donnerwetter, what a fine work. By the way: how did this german phrase find it´s way onto this british plane? Do you have an idea?

26 January 2022, 17:30

bughunter
The Clayton built B7190 was flown by Walter George Raymond Hinchliffe. He was commander of the C Flight of the 10👎 squadron RNAS in February/March 1918. He had been credited with 6 victories, survived the war but lost one eye in a crash. I continued to fly (with the one eye) for civil airlines until 1928. He was lost during a flight across the Atlantic.
The background of the german "Donner-Wetter" is not known, but it matches the devils and thunder flashes on the wheel markings.

26 January 2022, 17:46

Robin (WhiteGlint)
Jawdropping work! 👍

26 January 2022, 19:28

Bernhard Schrock
Picture 107: true rubber band. You attention to detail and original materials is unbelievable!!!! Picture 137: the terminals look great.

26 January 2022, 19:52

bughunter
Thank you mates!
The amount of details depends on the available references, and here I have a set of fantastic high resolution pictures of a flying Camel. That helps a lot!
And regarding the terminals: yes, we live in "Golden Times", so many nice accessories are available now. Not long ago I had to made my own ones for the Bristol Fighter, and now there are better ones which are even easier to work with 👍
At the moment I'm working on the remaining rigging, now with double wires and more ...

27 January 2022, 16:59

bughunter
You don't think that incitement is without consequences?!?!
Now the most crazy part I have ever done!

28 January 2022, 17:22

Robert Podkoński
I am just speechless now... I wouldn't even dare to ask about your remaining superpowers, bughunter 😉

28 January 2022, 17:27

gorby
I had to check to see that you hadn't swapped your usual scale for 1/8th for this build.
Astounding!

28 January 2022, 17:35

Spanjaard
jaw dropping!!!

28 January 2022, 18:43

Pepe
What to say that has not already been said..... Incredible masterpiece

28 January 2022, 19:37

Miguel Leandro
"!·$% impresive...

28 January 2022, 19:38

bughunter
Thank you very much mates!
@gorby I have the 1/8 Dr.I on the roof of my living room, but this here is really the new Eduard Camel, I swear!
@Pepe yes, a nice model, but I think the master piece are still the DH2 Stripdown and Bristol Fighter. Most closely to the original is still the Aviatik 30.40, hard to beat.
But yes, it is fun to learn with every model and try to get better! Cheers, Frank

28 January 2022, 21:20

Daniel Klink
so colorful and perfect looking once again Frank..
This is your playgound mate wow!!!!!!!!👍

28 January 2022, 21:24

bughunter
Jo Daniel, damit Du was zum Bestaunen auf dem Nachbartisch hast - wenn es denn mal wieder geht!

28 January 2022, 21:56

Michael Kohl
I just love watching mates going the extra mile. Very nice progress once again. That rigging turned out really beautifully but my favorite part is still the engine.

28 January 2022, 22:29

bughunter
Thank you Michael! I must admit that the extra mile is only possible with good references. As you may know I'm also active in the forum.ww1aircraftmodels.com and there is also a member James Fahey, who has released some fantastic set of pictures. Here his high resolution pictures of the Camel: jamesfahey.smugmug.com/Hi-Res-Camel/ But this is a later Camel, e.g. the undercarriage is different and it has a Clerget engine.

29 January 2022, 12:51

Jennifer Nijhuis
This is so amazing. Ich würde mir beim Versuch die Seile anzubringen die Finger brechen.

29 January 2022, 21:19

bughunter
Danke Jennifer, freut mich, daß Dir die Camel gefällt!

30 January 2022, 12:17

bughunter
Now the tail with a lot of control wiring and rigging is done! The ailerons will be the last step, as I won't be able to put the Camel on its back so easily.
There is a light at the end of the tunnel, or is it an oncoming train?

1 February 2022, 18:29

Pepe
Wooow....

1 February 2022, 19:05

Hanno Kleinecke
I'm absolutely certain it's not Victor Charlie with a lantern…… 😄
The tailplane looks superb with all the control cables installed !
Do you know what the story is behind the „Donnerwetter" being written on the fuselage ?
Not the most british term I would say ?

1 February 2022, 19:07

bughunter
Hanno, see my answer from 26. January, there I wrote all my knowledge about the pilot.
Now I know more about the squadron, the A-Flight has black stripes, the B red ones and the C blue. Eduard released today a new Profipack of Clerget Camels, which has the B6299 of the B-Flight as possible marking (the one of my T-Shirt shown above)
[img1]
This time the red stripes are decals!

1 February 2022, 19:28

bughunter
There is one important part missing, but otherwise I can call this Camel finished.

2 February 2022, 17:38

Robert Podkoński
Let me guess - a pilot is missing here? 😄 Looking absolutely fabulous (even without propeller in place...;) )

2 February 2022, 18:21

Alec K
Another spectacular build 👍

3 February 2022, 02:35

JW
Beautiful work. The blue and white on the upper surfaces is really eye catching.

3 February 2022, 04:34

Christoph Kunz
I can't see the Quirl...🤔
Another Model in Bughunter-museum-style.

3 February 2022, 18:28

Bernhard Schrock
Mensch Kerl, langsam gehen mir die Superlativen aus: waschechter Hammer, Meisterwerk, Juwel, klasse-Arbeit, Supermodel... alles hatten wir schon mehrmals!!!
...
...
...
Modellbauerisches-Kunstwerk in Museumsqualität. So! Das hatten wir noch nicht🙂 genau!!

3 February 2022, 18:38

Erik
😄

3 February 2022, 18:57

bughunter
Thank you mates!
Sorry Robert, I'm not going to clutter up the cockpit with a little fat pilot so that you can't see any of the beautiful details in it 😉
And Robert and Christoph: yes, the airscrew is the mentioned missing important part. That will be again something special and my first paint job failed. Finally I removed the paints completely and start from fresh, so that will need more time.
Danke auch Bernhard für Deinen sprachlichen Jongleursakt 👍

3 February 2022, 21:07

Robert Podkoński
LOL 😄 (But he could just stand beside his "Camel"...)

4 February 2022, 07:32

Hans-Jürgen Haag
Einfach Spitzenklasse! Wie man sieht kann man immer noch was drauf setzen! Respekt!

4 February 2022, 08:23

Michael Kohl
And not to forget: OOB! (Just in case you thought otherwise for a moment) 😉

4 February 2022, 10:22

Neuling
👍👍👍

4 February 2022, 13:52

Ben M
Bughunter - a little fat pilot? I expect to see a teletubby in your next build!

4 February 2022, 14:52

bughunter
Thank you mates!
Ben, that bird was active long before TV was invented, so also no teletubby 😉
That build log reached its end, as the airscrew is finished and mounted with PE parts to the Camel. Once I have made the final pictures I will create a new album, attached to the project.
Thx for watching 👍

4 February 2022, 16:45

bughunter
With a little luck I was able to use some sunshine today to take the final pictures. Don't miss them: SCM Newsfeed

4 February 2022, 19:17

Spanjaard
Airscrew is the cherry in this fantastic cake (build)

4 February 2022, 21:07

Album info

Since I got this kit as a gift from my colleagues, this must now be the next project.
This seems to be a great kit so it will be mostly oob 😉

Camel & Co.

188 images

1:48

Completed

1:48 Camel & Co. (Camel F-1) (Eduard 11151)

1:48 Sopwith Camel Bentley engine (Eduard 648677)

All albums

View all albums »