1992 Honda Prelude Si VTEC - wip
Crap. Somebody put a Fujimi kit into the Aoshima box.
What's in the box?
Red plastics. I don't like it. In the newer kits by Fujimi, the parts are black molded. I know it because I have some in my shelf and compared them.
Under the tape are the mirrors. The picture was taken before the painting. Nearly forgot it.
Under the tape are the mirrors. The picture was taken before the painting. Nearly forgot it.
The body in red plastics too. The newer kit are molded differently.
My decals are defect. They have flaws
Red part are black completely
Sticked the floor pan and interior together.
Closed the holes for the rear deck spoiler
Already base coated
Nearly good. Some flaws in the passengers door :/
Clear coat is done 🙂
After a little wet sanding and polishing, I was through the rear ends edge 🙁 So I spotrepaired it. Crossing fingers how it turned out.
The paintjob (clear coat) went not that good. The trunk lid won't get the same glossy finish like the rest. The rest was perfect.
Another failure: cracks and crinkles. I was not in the mood to do a repair again.
So I stripped the paint...
...and fillered it again after wet sanding.
New year, new paint job. I'm satisfied with it.
Done.
The decals were not usable after the flood last summer.They have a lot of cracks. I cut them out and glued it with the paper in place. A medium thick layer hand painted clear cote make them looking not that bad. When the body is over the chassis it will be good enough.
So I'm done with it 🙂
I love that front. At last, I added metal stickers on the nose an the rear. They suck. What a tiny crappy work, when the stickers fall apart
The Prelude-Logo broke in three pieces. I did my best. The H fell apart in two pieces. At the back and at the front. I hate it. But it looks good.
Comments
8 9 October 2021, 12:07
Christian W
Thank you for your interesst!
To the dashboard. I'll take the LHD dashboard. It is constructed that way, that the decal will be placed between the top part and lower part. It looks like, that it mustn't be put on like a decal. I think it is good enough to cut it out an glue it in place somehow. I'll look at it by the time when I need it. I'll see, how bad it looks through the windows. If it will be seen, that it is worn, I'll scan the decals of another kit in my stash and replace it. I'm looking relaxed forward 😉
Thank you for your interesst!
To the dashboard. I'll take the LHD dashboard. It is constructed that way, that the decal will be placed between the top part and lower part. It looks like, that it mustn't be put on like a decal. I think it is good enough to cut it out an glue it in place somehow. I'll look at it by the time when I need it. I'll see, how bad it looks through the windows. If it will be seen, that it is worn, I'll scan the decals of another kit in my stash and replace it. I'm looking relaxed forward 😉
10 October 2021, 19:53
Christian W
Another round for the paint. Stripped the color and did it from the start up.
Another round for the paint. Stripped the color and did it from the start up.
2 January 2022, 12:14
Christian W
Thank you very much. There are tiny little / very small imperfections where I don't think, to lay my hands on it.
Thank you very much. There are tiny little / very small imperfections where I don't think, to lay my hands on it.
7 January 2022, 21:57
Christian W
Thank you very much 🙂
I think I've been done with ist the next days. There are less parts all together.
Thank you very much 🙂
I think I've been done with ist the next days. There are less parts all together.
14 January 2022, 09:07