Dragon Ju 88 G6

Comments

1 30 January 2018, 12:14

Stephan Ryll
Nice start Jens 👍

1 February 2018, 16:01

Bart Goesaert
idd a nice start.... is it a sanding queen so far? or is it a descent fit

2 February 2018, 11:39

Jens
Sand Queen 🙂 , Dragon Normal to buy, like the supply of putty to the store still has 😄

2 February 2018, 12:02

Rv
Nice work so far. This kit is quite good, but there are some parts that need a special attention. The engines for example require a lot of putty and sanding. Tale care to the attachment of the wings. Have a look to my Mistel, maybe it would help: Le Grand Duc : Mistel 1 | Album by Hikaru (1:48)

4 February 2018, 11:38

Jens
Thank you RV, I've followed your Mistel very closely, but I have to notice, Dragon differs in each type, I have Ju 188 E, Ju 88 C6 and Ju 88 C6 / N ready, there were even differences between Revell Ju 88 C6 / N and Dragon C6, even the so small Fw 190 A shows Revell or Dragon some trowels ......, the same, after the G6 I will also turn to the Mistel variants, stock of Dragon I have enough 🙂

4 February 2018, 12:24

Jens
The pulpit I have again removed, too much dust on the inside, the surfaces are filled, but now comes the connection to the fuselage, that's probably again a lot of sanding dust, the sandstorm is sure: D

6 February 2018, 14:38

Thomas Bischoff
what a fast progress on this putty queen! Looking at your pictures bring up memories of these sanding/fitting sessions of the past 🙂 Keep on - it's worth it!

8 February 2018, 14:30

Stephan Ryll
But looking good Jens 🙂

8 February 2018, 16:28

Jens
Thanks for the motivational words 🙂

8 February 2018, 16:50

Jens
Basic color RLM 76 of Model Master, at the tail of a plastic remnant is inserted, which is the receptacle for the antenna wire, the sec. glue closes the "gap" without worry

9 February 2018, 07:47

Wilfried Tersago
Another kit that's high on my list... good work so far, Jens. Looking forward to the next steps!

11 February 2018, 09:51

Jens
Thank you Wilfried, but if you want to have the G6, then ICM has something of modern shapes and it would consume significantly less filler 😉

11 February 2018, 09:56

Gerald
Very nice Jens 👍

11 February 2018, 09:57

Jens
Danke Gerald 🙂, langsam finde ich zurück in die Plastikwelt 🙂

11 February 2018, 09:59

Gerald
Das freut mich zu hören Sehr gut 😉

11 February 2018, 10:10

Jens
Thanks James, I'm glad that it slowly comes to an end, the Radarnase had to be glued again, so again spatula, but I have wax spatula, so that's a little more comfortable 🙂 more pictures tomorrow in the light 🙂

13 February 2018, 18:54

Soeren R.
Really nice work Jens 😉

15 February 2018, 13:51

Jens
Danke Sören, langsam fluppt es wieder 🙂

15 February 2018, 14:21

Soeren R.
Das freut mich sehr zu hören 😉
Dann kann man sich in naher Zukunft ja auf ein paar Speedbuilds einstellen 😉

15 February 2018, 14:38

Jens
ich denke ja, ein klein wenig hab ich noch an Vorrat 😄, Zeit ist ja immer für den Spass 🙂

15 February 2018, 14:42

Thomas Bischoff
very nice!

15 February 2018, 21:30

Jens
Thanks Thomas, I certainly do not have the ambition and the passion like you, the talent even less, the more your words honor me, thank you 🙂

Danke Thomas, ich habe sicher nicht den Ehrgeiz und die Leidenschaft wie du, das Talent noch weniger, um so mehr ehren mich deine Worte , danke 🙂

15 February 2018, 22:04

Stephan Ryll
Jens, die Maschine ist wirklich sehr schön geworden 🙂 ich hätte mir bei den ganzen Antennen und Kabeln sicherlich die Finger gebrochen.
Von mir gibt es ein top 👍

16 February 2018, 19:55

Jens
Danke Stephan , die Finger sind heile geblieben, aber anfassen sollte ich die Diva nicht mehr, die Antennen sind extrem flüchtig 😄

16 February 2018, 20:03