Logo
base de datos de modelismo a escala | gestor de almacén

FCM 36

WWII French Light Tank

ICM | No. 35336 | 1:35

Boxart FCM 36 35336 ICM

Hechos

Marca:
ICM
Título:
FCM 36 WWII French Light Tank
Número:
35336
Escala:
1:35
Tipo:
Kit completo
Publicado:
2020 Nuevos moldes
Código de barras:
4823044406463 (EAN)
Tema:
FCM 36 Light Tank » Tanques (Vehículos)

Contenido de la caja

Dimensiones:
315x235x45 mm (12.4x9.3x1.8 inch)

Peso:
300 g (0.66 lbs)

Boxart diseñado por Valery Petelin

Línea temporal del producto

 
ICM
Revell
Heller
Historia completa »

Instrucciones

Descargar 5915Kb (.pdf)

Mercado

Tiendas en línea
Logo Super-Hobby.com
USD 41.15
PLEn stock »
Logo Plastic Models Store
USD 45.99
UAEn stock »
Logo Squadron Hobbies
USD 46.49
USEn stock »
Logo Hobbylinc.com
USD 50.09
USEn stock »
Logo MegaHobby.com
USD 64.79
USEn stock »
Logo Kitlinx
USD 57.59
FRDisponible »

Mostrar todas las ofertas » (14 en total)

SKU alternativos para ICM 35336:
ICM-35336 | ICM35336 | ICM 35336

Nota: Los precios y la disponibilidad son sólo indicaciones. ¡Compruebe si el producto realmente coincide!

Productos relacionados

ATL-193
FCM 36 / FCM 36 PAK 40 / 10 cm le FH 16
Friulmodel 1:35
ATL-193 2022 Nuevos moldes Multitema (2)
35842
FCM 36 Tracks
FC Model Trend 1:35
35842 2021 Nuevos moldes
35838
FCM 36 Side Grille Doors
FC Model Trend 1:35
35838 2021 Nuevos moldes
35 DEC 005
Decals FCM 36
Blitz 1:35
35 DEC 005 201* Nuevos moldes
CM-075
Workable Track Link Set for FCM36 (Plastic model)
Chino Model 1:35
CM-075 2022 Nuevos moldes

Todos los productos relacionados » (8 en total)

Revisiones de caja

Reseñas externas
Anuncio
kitreviewsonline.de
Revisión en caja
kitreviewsonline.de
Panzer Modell
Revisión en caja
Panzer Modell
Revisión en caja Modellbau-Koenig

Todas las reseñas » (9 en total)

Revistas

(Airfix Model World Issue 128)
Airfix Model World | Issue 128
English (TOC: 21 lines)
July 2021
(Tamiya Model Magazine 310)
Tamiya Model Magazine | 310
English (TOC: 11 lines)
August 2021
(Military Modelcraft International Volume 25 Issue 09)

Todas las revistas » (3 en total)

Proyectos

FCM 36
12 imágenes
View album, image #1
1:35
Proyecto: FCM 36
1:35 FCM 36 (ICM 35336)1:35 FCM 36 (MasterClub MTL35189)1:35 FCM 36 PE-detail set (Microdesign MD 035408)
FCM36
107 imágenes
View album, image #87
1:35
Proyecto: FCM36
1:35 FCM 36 (ICM 35336)1:35 FCM 36 PE-detail set (Microdesign MD 035408)

Galería

FCM 36 1:35
FCM 36
ICM 1:35
por Sungjun Jang en Panzer Modell

Comentarios

Ron Garcia
Nice kit. It goes together quickly, but I did run into a few minor problems, and I have a few suggestions.

1) You can add the tracks after completing the model. I added them right before step 26 so I could use the missing grills on the side to help guide the tracks though.

2) Speaking of the tracks, they come in two pieces per side. I don't know what they are made of, but plastic cement doesn't work on them. Somehow, you are supposed to connect the ends together using two microscopic holes. I could not figure out how to do this, as the pins are too short and soft to go through the openings (were there actually openings, though?). I stapled one section together since it would be hidden, and used CA glue with accelerator (and my wife's help) on the other end. Placed next to the rear road wheel, it looks fine.

3) The plastic is soft! I don't have a problem with this, but be careful when removing any excess plastic from the part or you will easily shave off a bit of the part. Also, part 38 snapped in two when I barely put any pressure on it while trying to slide it over the gun assembly. Not a problem because it is hidden, but it does illustrate how soft the plastic is.

4) If you can keep the coax MG from snapping off during assembly, I bow before your awesomeness! I almost made it, but it finally snapped off during one of the final steps of painting the complex camouflage pattern. Luckily, it landed right in front of me in clear view so I CA glued it back on - after the paint job was done! A stretched piece of sprue would have made an easy replacement.

5) It's pretty obvious but I'll say it anyway, to make your life easier, paint the completed roadwheel assembly before you add parts A5 and A12 . In fact, paint parts A5 and A12 before you add them to the kit to save yourself unnecessary masking.

6) I think parts A1 and A15 are reversed in the instructions. However, I fiddled around with both so much, in the end I wasn't sure anymore. By the way, be careful with the ends that stick out on both parts. I almost snapped off one because - you guessed it - super soft plastic.

7) Steps 24 and 25 were tricky for me. B4 and B5 didn't quite want to sit flush with the hull without some fiddling around with them. The same with the attaching the upper hull to the lower. I got it to work, but I did have to put a bit of putty on some tiny sections that were just a tad off.

8) The kit provides link by link plastic chains and one long chain that seems like metal but is very brittle. I used the long chin by simply cutting off the portion I needed. It worked fine.

So there you have it. The paint scheme probably took longer than actually building the kit. I really didn't know much about this tank, so I kind of like it better than some of the other early war French tanks I have been building lately. I think the look of the turret is unique. If you are trying to build all the Battle of France armor like I am, you should get this kit.
20 March, 03:35
Eugene PanzerBabay
Looking forward to release
15 April 2020, 16:37
PiotK
Great! I hope this means we can expect ICM to release a 7,5cm PaK40(Sf) auf PzKpfw.FCM(f) in the future, currently a missing link in the available (and affordable..) 1/35 Marder family.
1 17 January 2020, 09:38
Maciej
I've waited for this kit for years...finally!
7 January 2020, 10:00

FCM 36 Light Tank

Material de referencia

FCM 36 (Editions du Barbotin 7)
FCM 36
Trackstory No. 7
Pascal Danjou
2007

Todos los walkarounds » (1 en total)