Ki 61-I TEI Kobayashi
Kommentare
1 6 January 2019, 15:59
Steffen ArndtThank you! I am glad I could finally finish the cockpit (started just after X-mas). I only replaced the instrument panel and added a few parts from the Eduard set (plus of course the steel belts). The rest looks better in the box, IMHO. Then it was pretty straight forward to get something that looks like an aeroplane 🙂
6 January 2019, 22:29
Steffen ArndtHi Stefan, not your scale, huh.... also I am not sure I can push this project through, but I am trying.
7 January 2019, 17:52
Robert PaschallVery nice start, I'll watch this one as I have the Tony in my stash.
7 January 2019, 18:00
Stefan SchachtHallo Steffen, maybe, but I like your models and the Hien 🙂. Cheers Stefan
7 January 2019, 20:17
Steffen ArndtVielen Dank! Sadly it will take until the weekend before I can proceed with the kit
9 January 2019, 18:21
Daniel KlinkOf course i'm in! Fantastic detailwork so far STeffen...Looks amazing the cockpit 👍
9 January 2019, 18:30
Steffen ArndtVielen Dank! I hate to do cockpits, so I am glad you like it anyway
9 January 2019, 23:16
Steffen ArndtCheers Roberto! Today I added the tail planes and painted and installed the gun sight .. a bit late but it worked out. Then I added the windscreen.
I am not quite sure what to do with the area behind the seat. I will probably not add the PE because it cannot be see through the two clear plastic parts, but maybe I need to fill the seams...
12 January 2019, 21:23
Steffen ArndtI also added the resin exhausts by eduard .. these a a tad undersize so I filled the little gap
12 January 2019, 21:25
Daniel KlinkAh it is developing in a very good way 👍 Looks great Steffen 👍
@Holger better😉
9 March 2019, 10:30
Steffen ArndtThank you guys! @Holger: it is a new Tamiya kit ... it is what you would expect (I do not like their Bf 109G-6 though, that one is much too complicated)
9 March 2019, 15:11
Steffen ArndtI airbrushed the model yesterday in black as a primer. I first tried to sray AK Extreme aluminum directly on the surface, but it did not cover the flow marks (which you could not see on the bare plastic but were very proud on the metal surface. The blck has a slightly rough surface (see 2nd pic) so I gave it a slight rub with Zero Paints "Key and Clean".
9 March 2019, 16:29
Steffen ArndtNow with aluminum over black it looks the part. I will not do panel shading as stripes and blotches will take care of the uniform look...
10 March 2019, 08:43
Steffen ArndtToday I masked the tail and the recognition stripes - which were also red on this machine on the day I like to represent. 244th sentai was about to go for a larger attack with some special markings on the COs machine ... in the end it was cancelled, but there were some nice pictures taken that day
13 March 2019, 22:18
Steffen ArndtThank you, James. A little progress today: demasking and clear coat, but I'll leave it to dry before I take photos
14 March 2019, 21:03
Steffen Arndtthis morning the rising sun (😉 ) peaked below the clouds and thus I took the opportunity to take a picture of the current state of the model
15 March 2019, 15:36
Steffen ArndtThanks for the encouragement! Just started decalling it today .. still a bit of construction necessary too (e.g. some PE in the wheel bays..)
15 March 2019, 22:40
Steffen ArndtFirst couple of decals are on .. Tamiyas decals are a bit on the thick and stiff side, but they work o.k..
16 March 2019, 12:04
Steffen Arndttoday I started to apply the HGW wet transfers. Works quite well, but still a bit of touch up will be necessary. I have used XF70 for the first try .. still need to wait for the appearance of the dried paint
21 March 2019, 23:15
Steffen ArndtP.S. I left off pix of the wing maintenance decals applied over the past days...
21 March 2019, 23:16
Steffen ArndtThank you Guys! The camo transfers are applied. Still need to remove the carrier foil on the lhs. I screwed the wet transfers for the lower right engine covers so I had to paint these. On a closer look it is visible but from a feet away that should be no problem. Sadly I am running out of time and this will not make it to Lingen ... still a lot of work to do on the undercarriage (Eduard PE + Brassin)
22 March 2019, 18:53
Steffen ArndtWell, after a year of building other stuff it is probably time to resume this project. It was not shelved but just put aside as about 5 other projects that I consider rather as ongoing than stopped. I have just copied the picture from the book I have and took a closer look at the supercharger intake. This one is definitely not red but silver with camo dots. So I painted some green dots on it (roughly as on the pic).
7 March 2020, 17:50
Steffen ArndtThe wheel bay color is kind of a challenge. I have posted my question on Hyperscale and there is not that definitive answer. To stick with my XF-59 interior I have used the same paint with two drops of XF-5 added and a tiny bit of black. I got a nice khaki tone that is (in my book) a weathered sandy interior paint and fits nicely the explanations in the Lifelike instructions ... even though it might be totally wrong.
8 March 2020, 18:31
Steffen ArndtIn my lunchbreak today I airbrushed the whole model Tamiya X-22. Then this evening I gave the model a nice wash with water colours. This time I kept it on the black side because it improves the metal look but still there is some umber added
9 March 2020, 22:28
Steffen ArndtAfter the excess paint was removed it is starting to look the part... even though the camo hides a lot of it 🙂
10 March 2020, 12:38
Steffen ArndtI have started to tackle the undercarriage and drop tanks. The latter are Brassin items and were painted IJA light grey with black brackets. The mounts were airbrushed black then silver (one of the Tamiya rattle can stuff AS 12 or TS 30 .. I forgot which I decanted in what jar). Same for the undercarriage and wheels (Brassin) but I masked off the sections that should remain black. Afterwards the oloe strut sleeves were painted rubber black, as was the tail wheel roller. The dust cover was painted a greenish khaki colour (something that was standing in front of me, no idea what that was)
19 April 2020, 07:14
Steffen ArndtP.S. the silver areas got a black wash (Tamiya panel line stuff), the metal bands un the u/c legs were painted on.
19 April 2020, 07:17
Daniel KlinkThat is looking very good Steffen. The washing and dirt effects are on spot!
Love it.
19 April 2020, 08:55
Steffen ArndtThank you Daniel!
I have started to complete the undercarriage. I still need to mask and airbrush the red sections of the u/c covers but it is not looking to bad so far...
19 April 2020, 13:01
Steffen ArndtPainting was a bit difficult but worked out o.k. I lost one of the u/c door numbers from the Lifelike set and had to use the Tamiya decal instead .. it is not as obvious as I thought but still you can easily recognize the fatter Tamiya font.
To mount the inner u/c doors you need a section from the Tamiya part as Eduard did not make a replacement for the wheel well wall (they also do not mention it in the instructions. Watch out there is also a small segment of the wing attached to it that you need! All in all this is quite easy to do but hard to explain. Hope the drawings help a little. I'll add two more photos but I really do not like such close ups of my model kits.
25 April 2020, 16:51
Wim van der Luijtman.......just looking at that PE drawing for the UC doors gives me the creeps, I really don't like working with PE. I can never get the CA glue to work on those small bit....end result CA glue everywhere and parts not glued....But your Japanese bird is looking really good!
25 April 2020, 16:59
Steffen ArndtThank you guys! On these close ups I always see things that I could do better. e.g. I will need to fix the gap that opened due to the bending that was not planed.
25 April 2020, 19:00
Steffen ArndtProgress is slim. I have added the brake lines to the u/c legs and I have attached decals and fuel pipes to the drop tanks.
27 April 2020, 20:26
Steffen ArndtLots of small bits and pieces added. It is not difficult but takes time and nerves. I have added some parts in the wheel bays, attached the u/c doors and the small oil cooler (or whatever that is) from Quickboost. I mostly used Gators glue for these parts.
2 May 2020, 05:48
Wim van der LuijtLooking good, what's your experience with gator glue? I really don't like working with CA so an alternative would be welcome....
2 May 2020, 08:27
Steffen ArndtCheers Wim,
I do not like to use CA either. Gators glue is a white glue (acrylic) like the stuff you use to glue wood (e.g. Ponal here in Germany). You can thin and clean it with water (while not dried) and it dries transparent when not applied in too thick layers. Gators is optimized for modelling use and is a bit stronger than the normal wood stuff. It still is slightly flexible when dry which is a bonus as I often have CA fixed parts flying around at the slightest touch.
OTOH it dries not as fast as CA and the bond is not as strong on small surfaces so sometimes it is nice to first tack a part with CA and secure it with Gators against snapping or vice versa when you like to have some time to position a part. For parts like the hatches in the wheel bays Gators is a lot better. But I often use CA for resin wheels or other larger parts when strength and speed is required .. of course mixing 2K epoxy stuff is also an option but I prefer the easy use of Gators. AK has just issued something similar but I have not tested it yet
2 May 2020, 09:24
Steffen ArndtAero-Spezial here in Germany has it. Or you try from the source.
aero-spezial-modellb..end-44-ml::5040.html
aero-spezial-modellb..nd-44-ml::11670.html
gatorsmask.com/gatorglueorder1.html
2 May 2020, 09:30
Steffen ArndtThanks Holger,
yes, I am getting there ... still quite a bit to do and to avoid ruining it.
2 May 2020, 12:55
Steffen ArndtDanke Daniel! ... ist ja noch nicht fertig.
Just to show what I am doing right now: the Brassin guns are quite nice, but they are not hollow (which is a major drawback of all Eduard Brassin guns) so I drilled them out. I also had no resin venturi tube so I drilled out the kit part both ends with a conical chamfer and glued in a short 0.6mm Alu tube at the front end.
2 May 2020, 14:43
Steffen ArndtThanks Clifford!
So finally the flat coat is on, the prop is ready and many smaller parts already attached. I took a photo in my lightbox as it is pretty grey outside and this would lead to a grey appearance of the metal surfaces (just like on the real thing) ... it still has some metal shine though and in bright sunlight it will sparkle 🙂
3 May 2020, 06:24
Steffen ArndtAlmost there: I have added the antenna mast, the pitot, the rudder hinges, demasked the canopy and painted the sliding hood. I have attached the PE parts that replicate the seal between the wind screen and sliding hood. I still need to paint the position lights and attach the antenna
3 May 2020, 14:57
Roberto RocatWow. What a beauty! What about the green mottling? Was it hand painted? TIA.
4 May 2020, 20:54
Steffen ArndtThanks guys!
Roberto just look at the project inventory. I used HGW wet transfers .. which is kind of a decal (you remove the carrier film after application so you just have the paint on the model).
4 May 2020, 21:55
Lutz BertelmannThis is truly fantastic, I realy love the nice detail of the Cockpit! Very good!!
6 May 2020, 08:55
Daniel KlinkAlways an eyecatcher those Kobayashi schemra!
You did a great job on this Steffen👍
6 May 2020, 08:58
Steffen ArndtThank you Roberto, Lutz and Daniel! I am happy you like the finished model!
6 May 2020, 13:22
